Shipping calculator

Sale

Information

Contact Us

DAA

  • Cleaning rope-BORE SNAKE
    Cleaning rope-BORE SNAKE

    Simply the fastest and most convenient way to clean your gun barrel, be it a pistol, a rifle or a shotgun. Simply drop the weighted end down the barrel, from breach to muzzle and pull through. Do so with or without solvent, as best suites you needs. One pull runs a copper bristle brush as well as a wide long swab down the length of your barrel. You do not even have to disassemble the weapon to clean! Can be complete in seconds, and your barrel will be ready for another session on the range or in the field. 
     

    from16.00 EUR
    View details
  • Mini XL650 Case Feeder 9/38
    Mini XL650 Case Feeder 9/38

    Many customers choose to start reloading on their XL650 without the optional case feeder, and for them the new DAA Mini Case feeder will be a great addition to their press!

    In a few short minutes, perhaps while watching your favorite You Tube Channel, you can pre-hand-load the 6 tubes of the magazine assembly which will hold a combined 150 pcs of 9mm brass (about 130 of .40, or 120 of 38S).

    Using the included custom adaptor piece, you simply seat the Magazine atop your XL650, click the first tube into place – and you are ready to go. Each time a tube empties out, click the next one into position and continue reloading.

    Additional Magazine Assemblies may be purchased separately should you wish to prepare more than 150 pcs of brass before starting to reload.

    - The magazine assemblies are not caliber specific, and can be used for 9, 38 or .40 brass. We do not have a solution for .45 at this time.

    - The adaptor part IS caliber specific, with one being suitable for 9/.38 and another being for 0.40.

    - When filling the tubes, rotate the base of the assembly so that it is positioned between tubes- that way none of the columns line up with the hole in the bottom – and the brass won’t fall out prematurely.

    - You can use the 9/.38 kit for 38SPL or .357 however you will need to modify slightly the bottom of the adaptor - shorten the stem.


    from54.95 EUR
    View details
  • LED lighting system for Dillon 1050
    LED lighting system for Dillon 1050

    >span class="s1">The system comes complete with a 220/110 plug in adaptor, onoff switch, wire routing anchors and install kit. As with all Inline Fabrication lighting systems, these have our lifetime "No worries" warranty.

    from45.00 EUR
    View details
  • LED Lighting system for Dillon 650
    LED Lighting system for Dillon 650

    The Skylight kit for the Dillon 650 has a machined bushing with an embedded high output LED pod that installs into the center hole of the toolhead,  additionally, the system also has a 4" 6 LED strip that attaches to the inside of the press frame.   Super bright, , out of the way, no heat and does the job perfectly.  Average lifespan is 75,000 hours, that is about eight and a half year, but you have to reload 24 hours, seven days a week, all that time.

    Caliber changes are quick and easy, just pop it out, swap your toolhead, pop it back in and get to back work. The system comes complete with a 220/110 plug in adaptor, onoff switch, wire routing anchors and zip ties. As with all Inline Fabrication lighting systems, these have lifetime "No worries" warranty.

    from47.50 EUR
    View details
  • Range Ready Cleaning Kit
    Range Ready Cleaning Kit

    The FIRST EVER cleaning kit truly custom-made for IPSC / IDPA shooters !

    The CED/DAA Range Ready Cleaning Kit includes everything needed for calibers ranging from .22, 9mm/38 Super, .40/10mm, and .44/.45 Cal.

    Designed to fit  comfortably into your range bag, the Range Ready Cleaning Kit opens to reveal a rubberized  36x43cm cleaning mat built right into the kit itself. The mat, made of durable PVC material, is the perfect workstation for your field repairs and pistol cleaning needs. The non-slip surface prevents parts from getting lost and is easy to wipe clean after use. When finished, simply fold and zipper close. The entire Cleaning Kit measures only 20x30x3.5cm and easily stores away inside your CED Professional Range Bag or Shooters Back Pack.

    The Range Ready Cleaning Kit comes packed with custom features and tools. Included are all the brushes and swabs needed for proper gun care, two utility brushes with storage cases, a custom two-head brass / nylon hammer, a custom hex key set in both metric and standard sizes, a 4-bit custom screwdriver set, a plastic storage case for storing brushes & parts, a custom steel punch set, a stainless steel double-head cleaning tool for tough to reach areas, cleaning rod with patch loop tip, cotton cleaning patches, wired extractor/firing pin cleaning strips, & a 0.5 oz bottle of the famous Shooter’s Choice FP-10 lubricant, all designed specifically to fit into our compact, convenient and very functional cleaning kit.

    An extra clear plastic zippered storage pouch has been included for essential replacement parts you might want to keep close on hand.

    Dimensions closed: 20Hx30Wx3.5D cm
    Dimensions opened: 40Hx50Wx1D cm
    Weight: 600gr

    Range Ready Cleaning Kit includes:
    1. Phosphor Brushes (3 pcs.) (9mm/.38 Sup., .40 Cal./10mm, .44/.45Cal.)
    2. Cleaning Swabs (4 pcs.) (.22 Cal., 9mm/.38 Sup., .40 Cal./10mm,.44/.45 Cal.)
    3. Stainless Steel Tornado Brushes (3 pcs.) (9mm/.38 Sup., .40Cal./10mm, .44/.45 Cal.)
    4. Nylon Brush (.22 Cal.)
    5. Double-ended Utility Brushes (2 pcs.) (Nylon / Phosphor) includesbrush storage cases
    6. Two-Head Hammer (Nylon / Brass)
    7. Custom 12 pc. Hex Key Set (1.5mm, 2.0, 2.5, 3.0, 4.0, 5.0mm & 1/20",1/16, 5/64, 3/32, 1/8, 5/32")
    8. 2 pc. Punch Set
    9. Cleaning Rod with Patch Loop attachment
    10. Stainless Steel Double-Head Cleaning Tool
    11. 4-Bit Custom Screwdriver Set (3.3mm, 5.0mm, 6.0mm, #1 Phillips)
    12. Shooter’s Choice FP-10 Lubricant Elite or DAA BlueSlick oil
    13. Wired Extractor / Firing Pin Cleaning Strips (20 pcs.)
    14. Cleaning Patches
    15. Rubberized cleaning mat
    16. Extra pocket for storing small items

    from65.00 EUR
    View details
  • CED/DAA RANGEPACK - IPSC shooting range bag
    CED/DAA RANGEPACK - IPSC shooting range bag


    The CED/DAA RangePack has the same top quality and detailing as the larger RangePack Pro. It is made from black Ballistic nylon with a smart bright inner red lining. It includes a rain cover neatly packed away in a concealed pocket, ready at hand to be pulled out and wrapped around the bag to keep it dry. The shoulder straps and back are densely padded to provide support and comfort, even when carrying the bag fully loaded. An extra pocket in the upper flap is perfect for storing documents and pens, and 5 large external pockets add considerably to the storage space available.

    Like the RangePack Pro, the RangePack is designed to fit perfectly on the CED/DAA RangeCart Pro, and includes the steel eyelets for this purpose.

    - Weight: 2.5 kg (5.4 lb.) excluding accessories
    2.9 kg (6.4 lb.) with all accessories
    - Total Dimensions: 46 H x 36 W x 26 D cm
    - Bottom Compartment: 12 H x 30 W x 22 D cm
    - Top Compartment: 33 H x 30 W x 22 D cm


    Accessories included:
    - A red zippered Pistol Sleeve
    - A red Universal Pouch
    - Customized rain cover
    - Cable combination lock
    - Custom external rig strap

    from165.00 EUR
    View details
  • MR.Bulletfeeder 9mm
    MR.Bulletfeeder 9mm

    Mr. Bulletfeeder
    Anyone and everyone who invested in a Bullet Feeder absolutely loves it. You wonder how you ever reloaded without one...

    If you reload a lot, you quickly appreciate the efficiency and reliability of this ingenious patented system.

    We are proud to introduce the new Mr. Bulletfeeder® by DAA. The new system is lighter in weight and more compact than the previous models. It is easier to install and set up, and has a more professional “production” look and feel.

    An entirely new US Patend Pending dropper system allows the new model to function better and longer than before. The new dropper design eliminates the need for any spring or small plastic parts in the dropper head, and works entirely powered by gravity and an ingenious geometric design.

    And to top it all off - we can now offer the new system at a far more affordable price.
    If you have never tried a bullet feeder on your progressive reloader - what are you waiting for?! It cuts the time and effort involved in reloading practically in half! A must-have item for any serious shooter.

    The expanding powder funnel supplied is for the Dillon reloading machines only. Not compatible with other brands. To use with the LnL press, you will need to purchase their expanding powder funnel separately.

    The new Mr.Bulletfeeder is available in 9/38, 40SW/10 mm, .45. Rifle calibers .223 and .308.
     

    from429.00 EUR
    View details
  • Maglula Uplula
    Maglula Uplula

    Uplula, divice to load and unload your magazines. Easy and quick loading and unloading. The UpLULA loader is a military quality personal universal pistol magazine loader. Easy and quick loading. Rounds just drop in with no fingers pushing or forcing the rounds.
    Up to one round per sec. loading rate, with some practice.
    Fits in your hand and pocket, weighs only 66 grams (2.3 Ounce).
    Highly durable - constructed of the best reinforced polymer.
    No more strain or pain when loading those mags!

    from9.95 EUR
    View details
  • Mr.Bulletfeeder 12V DC Power Supply
    Mr.Bulletfeeder 12V DC Power Supply

    A replacement DC powder supply for your Mr.Bulletfeeder by DAA. This power supply includes two AC power cords, for EU and US Plugs.

    Input: 110-220v AC
    Output: 12V – adjustable.


    This DC power supply will allow you to adjust the speed at with your collator turns, to adjust for best performance.

    It includes a power surge protection, preventing more than 800mA from being supplied, even if the motor stalls. This prevents damage to the motor and the power supply, and eliminates the need for a fuse.

    from18.50 EUR
    View details
  • Tube Assembly 9/38/40 for Mini XL650 Case Feeder
    Tube Assembly 9/38/40 for Mini XL650 Case Feeder

    An additional 6-tube Magazine Assembly for your Mini XL650 Case Feeder.

    It will hold about 150 pcs of 9mm brass, 130 pcs of .40 and about 120 pcs of .38S.

    Tip:

    When filling the tubes, rotate the base of the assembly so that it is positioned between tubes- that way none of the columns line up with the hole in the bottom – and the brass won’t fall out prematurely.

    from44.95 EUR
    View details
  • Magnet inc. screw and countersunk nut
    Magnet inc. screw and countersunk nut

    A simple and effective solution for mounting a large magnet onto the DAA Single stack Racer Pouches.

    Set includes our large 42mm N42 powerful magnetic, a countersunk M5 nut and a 12mm M5 screw.

    You should first decide on, and lock the pouch in your angle of choice, as once the magnet is assembled, access is more difficult to the center mounting screw.

    from17.95 EUR
    View details
  • DAA Dust Cover
    DAA Dust Cover

    The DAA Dust Cover is made of durable long-lasting polyester 600D and features a slick “no-snag” lining to ensure easy-on-easy-off usage.

    The double layer material and thin padding offer good protection to your valuable firearm without becoming too bulky or taking up too much space in your range bag. The material flaps beneath the sturdy zipper ensure that neither dust nor rain get onto your gun.

    Each pistol cover includes a handy transparent ID pocket for placing a business card or competitor's badge to ensure that you and your dust cover can be reunited if separated on the range.


    Available for right-hand shooters only and Standard (for Standard and Production guns).

    from15.95 EUR
    View details
  • DAA MAGNET WITH CR POUCH MOUNTING BRACKET
    DAA MAGNET WITH CR POUCH MOUNTING BRACKET

    For those who want to take advantage of option to mount the magnet to their CR speed Versa pouch, but do not wish to purchase another CR pouch, we offer this DAA Magnet – with CR mounting bracket.


    This magnet is professionally mounted to a custom aluminum bracket, which is drilled and fitted for mounting on a CR Speed Versa Pouch. All you will have to do is open the main screw of your pouch, and assemble the magnet on the front end.

    The bracket is black anodized..

    THE CR SPEED POUCH IS NOT INCLUDED IN THIS PRODUCT!

    from24.95 EUR
    View details
  • DAA Pro belt
    DAA Pro belt

    The DAA PRO Belt includes all the superior features of the long running DAA Competition Belt, and lifts them up a notch!
    The quality and workmanship of this belt will make any owner proud! It features an attractive new dual-tone webbing on the outer belt and logo text on the inner. It includes a new unique name tag holder sewn into the outer belt webbing. You can now insert contact info and if you ever forget or lose your expensive rig, an honest finder can return it to you! A new rubberized DAA logo security loop completes this luxurious shooting belt.

    The DAA PRO Belt is available in dual-tone Black, Blue, Red or Silver-Grey, with the color boldly displayed in the wide middle section of the belt. 

    How to select the correct belt size: (do not select based on your pant size!)
    1. Measure you actual waist circumference at the height where you plan to wear your belt.
    2. Convert your measurements into Inches (1inch = 2.54cm)
    3. Order the belt size which matches your measurement. Round upwards: if you measured 39”, order a belt size 40”.

    from59.00 EUR
    View details
  • Double head hammer set
    Double head hammer set

    Double head with brass, nylon, rubber and steel heads.

    Custom designed for range use, this value packed double-head hammer will cover all your pistol repair needs. The hammer’s compact and light weight size make it an ideal handy addition to any range bag or work bench.

    from18.00 EUR
    View details
  • HARD CASE SMALL-235
    HARD CASE SMALL-235

    Hard Case Small-235 are IP67 certified, tough, durable and reliable. They may be used in a variety of applications, ranging from firearms and valuable transport, to marine, photography, scuba diving, hunting, fishing, special corps and much more. They are ultra-compact and light weight – making them perfect for Air Travel, where weight is often an issue. And although they are small – they can hold two full size Standard pistols. (too small for Open guns though..)


    An added bonus is that their small size allows them to fit snugly into the lower compartment of the CED/DAA RangePack (Medium backpack).

    These cases offer superior protection from the elements, water, dust and impacts, making them suitable for a wide array of sectors and applications.

    The DAA Hard Case Small-235 cases are shipped including a 5 piece set of foam: 1 egg-shell layer of foam in lid, and beneath that two thick precut-cube foam layers, and two hard layers of 10mm foam, allowing you to pluck-out the shape of the valuables you wish to transport in the case, and create two layers to transport two guns, one on top of the other.

    Features include:
    · Watertight seal around lid
    · Automatic pressure release valve
    · Two easy to open double throw latches
    · Load tested soft grip handle
    · Holes for double padlocking
    · Stackable interlocking system
    · Thick body material
    · Extra fixing points
    · Full length hinges
    · Pick N Pluck foams in the bottom and convoluted foam in the lid available as standard
    · Rectangular DAA resin logo on the lid
    · Available in Black or Orange color

    External dimension: 258 x 243x 118 mm/10.16 x 9,56 x 4.64 inch
    Internal dimensions: 235 x 180 x 106 (81+25) mm/9.25 x 7.08 x 4.17 (3.19+0.98) inch

    from43.00 EUR
    View details
  • Shell sorter 3 piece set
    Shell sorter 3 piece set

    The Shell Sorter™ is a simple product designed to reduce the time spent sorting brass by caliber, allowing you to enjoy more time reloading and shooting.

    The Sorter simply sits on top of a common 5 gallon bucket, with a few shakes your brass is sorted by caliber. The Shell Sorter™ is comprised of three pans designed to sort several common calibers.

    The three main calibers that most reloaders sort are 45 ACP, 40 S&W, and 9mm. We have labeled the sorters according to those three main calibers. The sorters do sort many more calibers!

    The fastest way to sort is to stack all three of the pans together with the yellow pan on top, and the black on the bottom, in that way all your brass is sorted at the same time.

    If you sort before tumbling as is recommended, most shells that are inside of each other will come apart with the shaking and are sorted correctly. However, if you tumble first, those are likely to jam together with small bits of media, and sometimes those require pliers.

    The sorters can also take the place of your media sifter. Just tumble, pour your brass into the appropriate sorter(s), shake a bit, your media is in the bucket, and your brass is ready for the next step.

    You can use this on the range so that you only bring home brass in the calibers that you reload.

    The Shell Sorter™ is made of ABS, a very strong plastic which will give a lifetime of service. We placed a sorter underneath a car tire, and it didn't break or distort! In fact, it still worked!

    Always wear gloves and a dust mask when working with used brass because of the levels of lead dust present.

    from59.00 EUR
    View details
  • Silicone Gel Replacement Ear Pads DAA
    Silicone Gel Replacement Ear Pads DAA

    The DAA Silicone Gel Replacement Ear Pads are a set which includes two silicon ear pads and 2 new foam insulation cushions. Models are available to fit the line of MSA Sordin Electronic ear defenders, and an additional model designed to fit the 3M Peltor ear defenders.

    The Peltor model has been tested and found to perfectly fit on the Sportac, WS Sportac, Protac III, Sport Tactical 100 and the X4A passive. They should fit the entire Peltor lineup.

    The DAA Silicone Gel Replacement Ear Pads greatly improve both the comfort and performance of your current pair of ear defenders. The Silicone in the pads is in a gel state, which ensures no leakage, even if the tough outer layer is somehow punctured. The pads slightly increase the space available for the ear, improving comfort of wear over long periods. The gel pads better molds themselves to the shape of your head, and seals perfectly around the side-arms of your safety glasses to ensure improved sound protection levels when compared to your normal foam/robber/plastic pads, as supplier with your original hearing protection. You need to try it to believe it - the improvement is HUGE!

    The two models available are precisely engineers to easily, but firmly click into place onto the ear defenders and stay put. The gel portion of the pads is welded (not glued) to the sturdy plastic base, ensuring that it will never separate or come loose, even if you leave them in a hot car for a week.

    The DAA Silicone Gel Replacement Ear Pads will improve the sound protection, performance and comfort of wear of any Sordin or Peltor model set, and serve you well for years.

    from29.95 EUR
    View details
  • DAA PSP Brush for Dillon
    DAA PSP Brush for Dillon

    The DAA Powder-Spill-Prevention (PSP) Brush is a simple yet efficient reloading accessory that solves a real issue: How to prevent small amounts of powder being spilled out of the case, as the tool head of the progressive reloading press indexes?

    from17.95 EUR
    View details

Contact Us