Shipping calculator

Sale

All products on Sale

Information

Contact Us

Accessories

  • DAA 2-IN-1 SEATING AND CRIMPING DIE
    DAA 2-IN-1 SEATING AND CRIMPING DIE

    A common question we hear is “Can I use the Bullet Feeder on my 550?” Or “Can I use the Bullet Feeder and still continue to use my powder check on my 650?”.

    Such Seating and Crimping dies are available, and so we decided it was time we made them directly available to our customers as well. LEE Precision produces these, so no question about the quality. 

    The 2-in-1 Seating and crimping die include an O-ring lock machined into the nut, which allows you to hand tighten only – and the die stays put! They include a finger adjustable floating bullet seater. For durability they are heat treated to ideal hardness and polished to the smoothest finish.

    from27.00 EUR
    View details
  • MR.BULLETFEEDER BY DAA POWDER FUNNEL - DILLON
    MR.BULLETFEEDER BY DAA POWDER FUNNEL - DILLON

    MR.BULLETFEEDER BY DAA POWDER FUNNEL - DILLON

    from35.00 EUR
    View details
  • SUPER SWAGE 600
    SUPER SWAGE 600

    Until now, reusing military brass, with its crimped primer pockets, has been a tedious task. The Dillon solution is a remarkably simple device that bolts to your bench and allows you to swage the primer pockets with speed and ease. The case is supported from the inside, so you won't be tearing the rims off the brass. A tool steel, hardened swage rod (easy to change from large to small primers) simply rolls the crimp away. No reaming is necessary. Our unique compound cam leverage system assures not only ease of operation, but perfect alignment with each and every round. Sound simple? It is and it works. What's more, it's inexpensive. The Super Swage 600 comes with large and small swage rods, .22 and .30 caliber backup rods, and a 45ACP adapter. 

    from136.29 EUR
    View details
  • DAA Kinetic Bullet Puller Hammer
    DAA Kinetic Bullet Puller Hammer

    The DAA Bullet Puller is a must-have for serious reloaders. This tool takes all the hassle out of separating your used cases from the bullet and powder. The tool itself is formed from high-quality plastic with an aluminum rod to ensure many years of durable performance.

    The DAA Bullet Puller can be used for ammunition of all sizes ranging from .17 Remington to .50/70 Government cases. This tool comes with an extra set of three collets, should the originals happen to break. The tool itself is virtually indestructible and makes quick work of disassembling your ammunition for reloading.

     

    from24.95 EUR
    View details
  • Mr.Bulletfeeder Dropper die threaded body
    Mr.Bulletfeeder Dropper die threaded body

    A replacement threaded die body for your Mr.Bulletfeeder by DAA Dropper. This threaded body is compatible with all calibers.

    from13.50 EUR
    View details
  • Metal Stencil for Marking Ammo
    Metal Stencil for Marking Ammo

    Some people mark brass to keep up with how many times it has been fired and some people mark their brass so they can later identify brass ownership. We designed Brass Stencils that are specially designed for marking ammo. This stencil is fully compatible with our 100 rnd case gauge. Each stencil set comes with 1 colour marker. You can use any permanent marker that only leaves thin layer if color and does not leave any coat of lacquer that may reduce firearm reliability. Brass Stencils are made from stainless steel and are quick to assemble and easy to apply, the solvent resistant plates can be used again and again.


    from24.90 EUR
    View details
  • Case Feeder Stop Switch for Dillon 1050
    Case Feeder Stop Switch for Dillon 1050

    Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.

    from24.80 EUR
    View details
  • MR.BULLETFEEDER OUTPUT SPRING AND EXTENSION ADAPTOR
    MR.BULLETFEEDER OUTPUT SPRING AND EXTENSION ADAPTOR

    Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

    To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

     Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machines and the large size (12mm inner diameter) as shipped with the pistol calibers.

     Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

    from9.50 EUR
    View details
  • MR. BULLETFEEDER - DROPPER ASSEMBLY
    MR. BULLETFEEDER - DROPPER ASSEMBLY

    The Dropper Assembly is needed for shooters who wish to set up a second tool-head in the same caliber, and wish to quickly transition from, say, 9mm to .38super. Or from one 9mm bullet to another. A change is needed to the collator parts, and if a 2nd tool-head is to be used on the progressive reloader, it is quicker and easier to leave an adjusted Mr.Bulletfeeder dropper on each tool-head. This allows for quick swapovers, without the need to calibrate or adjust the dropper. Note that in most cases you will need to purchase an additional Powder Funnel for your second tool-head’s powder measure, as our expanding powder funnel is required for troublefree reloading.

    from95.00 EUR
    View details
  • MR.BULLETFEEDER 2018 HANGER ASSEMBLY
    MR.BULLETFEEDER 2018 HANGER ASSEMBLY

    The 2018 Hanger Assembly for the Mr.Bulletfeeder by DAA ships as standard with all new units leaving DAA as of Jan 2018.

    Should you wish to upgrade your current hanger assembly (the one with the round Delrin pucks and aluminum rods) you can do so by purchasing this new hanger separately. It is reverse-compatible with all previous Mr.Bulletfeeder by DAA units.

    The new hanger is a simplified design, which makes assembly and adjustments to the tilt angle easier and faster to make. The Horizontal aluminum bracket clamps directly onto the motor gear box, allowing for easy assembly on either the left or the right side of the collator, to accommodate your specific position mounting needs.

    The vertical piece hangs over the side of your case feeder, and connects to the horizontal bracket by means of a large M8 bolt, which can be loosened and rotated for tilt adjustments.

    Sturdy attachment to the collator, a simplified design with fewer parts, thick aluminum profiles and way fewer screws make this hanger simpler and easier to setup and adjust.

    Note: Machine NOT included - only Hanger. 

    from29.95 EUR
    View details
  • Mr.Bulletfeeder output spring and extension adaptor
    Mr.Bulletfeeder output spring and extension adaptor

    Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

    To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

     Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machinesand the large size (12mm inner diameter) as shipped with the pistol calibers.

     Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

    from9.50 EUR
    View details
  • DAA Output Chute and Spring
    DAA Output Chute and Spring

    he DAA Output Chute can be attached to any reloading press, hanging onto the same bracket which usually holds the Akro-Bin, and replacing it.

    The long, 120cm (4ft) feed spring enables you to run the ammo down to a container on the floor, sparing you the need to empty that bin as you reload, and uncluttering your reloading press.

    from19.95 EUR
    View details
  • DAA Reloading Scale
    DAA Reloading Scale

    The DAA Reloading Scale is a compact-size scale packed full of the latest precision load-bearing technology. This new premium digital precision scale is designed to provide you with the most accurate, consistent information about your powder loads, in an easy to use and easy to calibrate package.

    The DAA Reloading Scale offers read-outs in either grams or grains. It has a load capacity of 20 grams (300 grains) and a division (precision) of 0.001 gram or 0.05 grain, far exceeding the precision offered by even more expensive models on the market. It features a stainless steel load platform and a blue colored backlight display.Accessories included: A hard storage and transport case, 2 x 10 gr calibration weights, a powder pan, tweezers, an antivibration mat and user manual. 

    Covered by a Double-Alpha two year warranty.

    from89.00 EUR
    View details
  • DILLON WRENCH / 1" LOCK RING 5-PACK
    DILLON WRENCH / 1" LOCK RING 5-PACK

    A characteristic of virtually all progressive reloading machines, regardless of brand, is that the dies are set rather close together. When you are first setting up a "naked" machine, there is plenty of wrench room, but if you have a need to adjust a die afterward, it often requires a delicate touch to maneuver a lock ring on a crowded toolhead. 
    Dillon Precision has addressed this in two ways. We now offer new 1" die lock rings and a 1" Bench Wrench to fit them. This combination gives much more room to re-adjust dies after they're already mounted. The opposite end of our new wrench is a 7/16" box-end for adjusting the Powder Bar of any Dillon Powder Measure. Our new lock rings fit any standard 7/8" x 14 dies.

    from16.80 EUR
    View details
  • Dillon XL650 Toolholder with a wrench set
    Dillon XL650 Toolholder with a wrench set

    Dillon's new Toolholder fits your XL 650 and ensures that the tools you need to service your reloader are handy and organized. No more digging around your bench trying to find the right size hex wrench! This unit includes a complete allen wrench set plus the one inch bench wrench.

    from46.20 EUR
    View details
  • DAA Golden 20-Pocket Gauge
    DAA Golden 20-Pocket Gauge

    Any competitor serious about his shooting is aware of the importance of drop-testing one's bullets before a match. Since most malfunctions are ammo related, and most of those relate to deformed, bulging or otherwise defective brass - dropping the bullets into a gauge is an effective way to reduce the chance of a costly malfunction. The problem has always been that it takes time! over 15 minutes at least, to test 400 rounds with a single bullet gauge or using one's barrel. Well not any more!

    We are please to offer you the DAA Golden 20-Pocket Gauges, available in 9mm, .38Super, .40SW or .45ACP. These gauges are machined from top quality aluminium, and the pockets are finished using Clymer finishing reamers, the same which are used by top gunsmiths worldwide to cut the final dimensions on the barrel. The 20 pockets allow you to drop the rounds in a lot faster than into a single gauge, cutting your testing time down to less than half of the time!

    A great deal of thought went into the dimensions of the block: The bullet pockets were positioned as close together as possible, to allow dropping 2 or 3 bullets in at a time, in the same way you would fill your ammo boxes. The height is purposely cut shorter than other gauges, so that the tip of the bullet head sticks out. If a bullet gets stuck, as reloaded ammo often does - you can simply push it loose from below with your finger, without having to pick up a tool.

    from47.50 EUR
    View details
  • Dillon Pistol caliber case gage
    Dillon Pistol caliber case gage

    Dillon handgun case gages allow you to check your handgun ammunition to ensure it will fit a minimum sized chamber. Made of stainless steel for long life.

    from22.05 EUR
    View details
  • Dillon RF100 Large conversion for Automatic Primer Filler
    Dillon RF100 Large conversion for Automatic Primer Filler

    This kit allows you to quickly, and easily convert your RF 100 Primer Filler to accept large primers (RF 100 Primer Filler sold separately).

    Dillon's RF 100 Automatic Primer Filler eliminates the task of filling primer pick up tubes. Now you simply pour your primers from their box into the top, press the blue button and watch it run!  In about two minutes the primers are inside the primer tube which is shielded inside a protective metal housing. Thats about 30 rounds you can load while the RF 100 is doing your work for you. Just top off the RF 100 each time you need more primers in your reloader and you'll have another filled primer magazine waiting for you when you need them. There is no need to purchase additional primer pickup tubes.  

    from57.75 EUR
    View details
  • Dillon Square deal wrench set
    Dillon Square deal wrench set

    Dillon's new Toolholder fits your Square Deal B and ensures that the tools you need to service your reloader are handy and organized. No more digging around your bench trying to find the right size hex wrench! This unit includes the complete allen wrench set plus the new Square Deal bench wrench.

    from40.95 EUR
    View details
  • Dillon Magnum rifle powder bar
    Dillon Magnum rifle powder bar

    The Dillon Magnum Rifle Powder bar throws charge weights from 50 grains up to approximately 72 grains of extruded powder, or up to approximately 82 grains of ball/spherical powder

    from46.20 EUR
    View details

Contact Us