he DAA Output Chute can be attached to any reloading press, hanging onto the same bracket which usually holds the Akro-Bin, and replacing it.

The long, 120cm (4ft) feed spring enables you to run the ammo down to a container on the floor, sparing you the need to empty that bin as you reload, and uncluttering your reloading press.

Some shooters prefer to have a muzzle support on their competition holster. This is an indisputable fact.

While most users will find that the Race Master holster functions perfectly without the additional muzzle support, there are some added advantages to using this extension: The muzzle support prevents the gun from being dislodged upwards, which could happen if bumped on the shooters thigh, or against a prop, during a walkthrough. If the holster was left unlocked, the gun can be dislodged. The muzzle support prevents this from happening.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machinesand the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

The DAA Deluxe Magnetic Pouch utilizes two powerful 32mm magnets to hold the magazine securely in place while providing a smoother release than that achieved from the larger standard Magnetic Pouch. The support side walls allow us to use smaller magnets which in turn make the pouches more useable as an all-round pouch for every day use, and not just as a designated pick-up Pouch.

For those shooters who like the simplicity and minimalist look of an open magnetic pouch - this is the perfect choice! The slim body make it possible to position pouches closer together while still leaving enough room to reach down and grab the magazine correctly. The lack of external or front pouch walls allow the pouches to be spaced that much closer together. Perfect for Standard or Production where one must wear the pouches behind the hip bone.

The pouch is attached to our new model belt hanger, which locks securely on any 1.5" belt, clamping down to hold tightly even on thinner belts. The pouch can be swivelled around the centre screw (lower magnet's middle) to angle the pouch as designed. The off-centre mounting point on the hanger offers the option of two heights to choose from. The pouch body is machined from solid Delrin and so is tough and durable. Available in Black only.

Available for Right-Hand users only.

The 2018 Hanger Assembly for the Mr.Bulletfeeder by DAA ships as standard with all new units leaving DAA as of Jan 2018.

Should you wish to upgrade your current hanger assembly (the one with the round Delrin pucks and aluminum rods) you can do so by purchasing this new hanger separately. It is reverse-compatible with all previous Mr.Bulletfeeder by DAA units.

The new hanger is a simplified design, which makes assembly and adjustments to the tilt angle easier and faster to make. The Horizontal aluminum bracket clamps directly onto the motor gear box, allowing for easy assembly on either the left or the right side of the collator, to accommodate your specific position mounting needs.

The vertical piece hangs over the side of your case feeder, and connects to the horizontal bracket by means of a large M8 bolt, which can be loosened and rotated for tilt adjustments.

Sturdy attachment to the collator, a simplified design with fewer parts, thick aluminum profiles and way fewer screws make this hanger simpler and easier to setup and adjust.

Note: Machine NOT included - only Hanger. 

The Dropper Assembly is needed for shooters who wish to set up a second tool-head in the same caliber, and wish to quickly transition from, say, 9mm to .38super. Or from one 9mm bullet to another. A change is needed to the collator parts, and if a 2nd tool-head is to be used on the progressive reloader, it is quicker and easier to leave an adjusted Mr.Bulletfeeder dropper on each tool-head. This allows for quick swapovers, without the need to calibrate or adjust the dropper. Note that in most cases you will need to purchase an additional Powder Funnel for your second tool-head’s powder measure, as our expanding powder funnel is required for troublefree reloading.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machines and the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

Many PCC shooters use extended Glock Magazines, often with long base pads added for even more capacity.

To ensure the best possible retention in our Racer and Race Master mag pouches, we are pleased to offer this dedicated extended Glock Side spacer.

Simply assemble this spacer instead of your short one, and allow the bottom of your long mag to extend out the bottom of the pouch body, for a more balanced more secure retention.

The long spacer offers three hole positions in which to place the stopper, giving you the ability to experiment and decide for yourself what the best depth for your magazine is.

NOTE:  this spacer is not compatible with the Alpha-X line of pouches. Magazine and Magazine Pouch not inlucded!

The DAA XL650 Debris-Out Casefeeder Adaptor is the answer to a real problem many reloaders are all too familiar with: when cleaning brass with corncob or other dry media, often small bits of media remain mixed with the brass, and are fed down the case feeder tube. When they reach the tighter diameter of the adaptor tube, they wedge against the cases, causing a feeding jam. You then have to stop reloading, take apart the feeding pipe, clear the jam and only then continue.

But with the new DAA XL650 Debris-Out Casefeeder Adaptor, which replaces the original Dillon case feeder adaptor on your XL650, the slots cut in the pipe allow the debris to fall out the sides onto the small collection tray (we like to keep our workbench clean and neat!) and the chances of a jam-up are greatly reduced.

A drop on fit to your Dillon XL650. 

Not suitable for use on other Dillon reloading models, and cannot be used in conjunction with the DAA XL650 Mini case feeder.

A replacement threaded die body for your Mr.Bulletfeeder by DAA Dropper. This threaded body is compatible with all calibers.