€ $
Tax settings
select country
Marke auswählen
 
Marke
Zurücksetzen (reset)

Napredno iskanje

Farbe
Größe
Preis
Zurücksetzen (reset)

Akcijska ponudba

Subcategories

Browse by category

Neu
Feuerwaffen
Feuerwaffenteile
Ausrüstung
Wiederladen
Instandhaltung
Optik & Visiere
Demo / Gebrauchte Artikel
Verkauf
Rahmenteile
Schiebeteile
Abzugssystem
Griffe & zusätzliche Rahmen
Federn
Magazine & Magazinböden
Einreihiges Magazin
Zweireihiges Magazin
Base Pads
Springs & followers

Pistole

Nach neueste Artikel sortieren
24 Pro Seite
BUL SAS II Magazine 126mm 9x19 G2
€57.34  
Auf Lager
Stay-Tech StayHEX23 Grips for KMR Spectra
€65.57  
Auf Lager
+ −
Stay-Tech StayHEX23 Grips for KMR Umbra
€65.57  
Auf Lager
+ −
ARMANOV Speed Line Magazine Base Pad CZ TS
€20.41  
Auf Lager
+ −
EEMANN Tech Competition Springs Kit for Phoenix
€40.98  
Auf Lager
+ −
Eemann Tech Ultimate Brass Long Grips for CZ SP-01, SH2, TS
€99.99  
X Large
Auf Lager
+ −
Toni system +6rd Magazine Pad Extension Glock 17/34 and Others
€36.89  
Auf Lager
+ −
Toni system Magazine Spring 31 Rounds for Glock
€7.38  
Auf Lager
+ −
MBX Alu Base Pad IPSC (140mm/170mm rule) Compliant Black
€36.80  
Auf Lager
+ −
Tanfoglio UNICA SF Magazine Catch
€36.89  
Auf Lager
+ −
platnice in lijak- Rjava
€118.84  
Auf Lager
+ −
Dawson Precission Insert for Ice Magwells STI/SV 2011
€21.52  
Auf Lager
+ −
Toni System Brass Counterweight Glock 19, 19X, 45
€55.76  
Auf Lager
+ −
BUL 1911/2011 Hammer Strut Pin
€1.64  
Nicht auf Lager
BUL 1911 Classic Alu Magwell
€72.13  
Auf Lager
+ −
BUL Bushing Mounted Magwell
€28.69  
Nicht auf Lager
BUL Hammer Strut Black
€9.84  
Auf Lager
+ −
-15%
Petelin Male roke (CZ 75, SP-01, TS, C
€20.83 €24.51  
Nicht auf Lager
CZ Shadow 2 Wide Safety Set - Right Handed
€81.96  
Nicht auf Lager
Tanfoglio 16rd SF Magazine for 9mm Black
€29.51  
Auf Lager
+ −
THUMB REST za desničarje - TANFOGLIO UNICA črna
€33.61  
Auf Lager
+ −
-50%
Firearms Traditional Frame MagWell for 1911-Black
€163.52 €327.05  


WEB

The Infinity Firearms® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

  • The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
  • These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
  • Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

  • Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
  • Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
  • Remove the mainspring housing by pulling down.

Attachment Instructions

  • Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
  • Assemble the gun including the specially machined mainspring housing1, but do not insert the mainspring housing pin.
  • Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
  • Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
  • Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

1 - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.

Auf Lager
+ −
-30%
Firearms Traditional Frame MagWell for 1911-Black
€228.93 €327.05  


WEB

The Infinity Firearms® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

  • The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
  • These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
  • Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

  • Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
  • Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
  • Remove the mainspring housing by pulling down.

Attachment Instructions

  • Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
  • Assemble the gun including the specially machined mainspring housing1, but do not insert the mainspring housing pin.
  • Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
  • Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
  • Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

1 - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.

Auf Lager
+ −
Nabojnik Taurus TX 22 16RDS .22lr
€35.98  
Auf Lager
+ −
1 2 3 4 5 6 7 8
2 - 16