Pistola

Original CZ Buffer

CGW’s new P-10-C short reset trigger.   Drops in and produces a reduction in pre-travel.  Deep inside the trigger we have installed a 3 mm x 6 mm pre-travel screw for those that want to custom tune their trigger for the ultimate in trigger control.  The trigger is curved to position the trigger finger in the center of the trigger, resulting in a more consistent trigger pull.  This curve also helps keep the trigger finger away from the bottom tip of the trigger.  Made from billet aluminum.

This trigger is longer than the stock P-10-C plastic trigger, and has been extended as close to the bottom of the trigger guard as reliably possible.  This longer trigger, combined with the curve, virtually eliminates  trigger “sting” or “bite”.  The center pivot is flush with the trigger face during use, resulting in a comfortable “all day” trigger.

Shadow 2 Reach Reduction Kit with ultra-short reset now USPSA Production approved.  Cajun Gun Works’ famous RRK that permanently re-positions the trigger rearward with the hammer fully lowered an amazing 5 mm’s and reduces single action pre-travel dramatically.  Includes our “old style” stainless steel 85C trigger “Made in the USA”  with pre and over-travel screws so you can custom tune to your CZ.

This not only relocates the trigger, but it also doubles as an ultra-short reset for single action.  

Includes 2 different hammer pins (1 x HPIN and 1 x 75009) so you can be assured a secure attachment to either the factory hammer or Cajun Gun Works hammer.  Lifetime warranty to the original purchaser

La molla speciale RC-tech è ridotta del 20% rispetto all'originale, cambiarla ti aiuterà con ricariche più veloci

si adatta alla maggior parte delle pistole CZ

Fits Cobra mags, Dawson mags, Trip mags and Metallform mags.

Precision cut with RC logo.

Also available are Magazin spring plates in brass. 

adds weight(50grams) to bottom for faster reload 

Take your Shadow 2 or Shadow 1 from great to OMG!  This will transform your S-2, delivering an ice crisp SA of 3 lbs. or less.   DA typically runs 6 lbs. or less using our famous HS-12000 (11.5#) hammer spring.   The disconnector will require minor fitting so you get the reset to a PERFECT 1 mm, which is not difficult to do with CGW tech support.  Turns the CZ lock work into a precision Swiss watch!  USPSA Production legal too!

MAGWELL for Shadow 2 

Speeding up your magazine insertion is one of the things to beat the competition. Also the grip with the Magwell feels beter. About the grips , they indeed need to be the short ones.

Here you find the short grips.

CZ Shadow 2 Safety Wide Right side, only Wing.

Slide stop spring pin CZ 75, SP-01

WEB

The Infinity Firearms^® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

• The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
• These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
• Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

• Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
• Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
• Remove the mainspring housing by pulling down.

Attachment Instructions

• Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
• Assemble the gun including the specially machined mainspring housing¹, but do not insert the mainspring housing pin.
• Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
• Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
• Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

¹ - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.