Накладки и шахта магазина

WEB

The Infinity Firearms^® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

• The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
• These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
• Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

• Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
• Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
• Remove the mainspring housing by pulling down.

Attachment Instructions

• Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
• Assemble the gun including the specially machined mainspring housing¹, but do not insert the mainspring housing pin.
• Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
• Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
• Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

¹ - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.

WEB

The Infinity Firearms^® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

• The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
• These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
• Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

• Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
• Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
• Remove the mainspring housing by pulling down.

Attachment Instructions

• Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
• Assemble the gun including the specially machined mainspring housing¹, but do not insert the mainspring housing pin.
• Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
• Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
• Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

¹ - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.

The newest compact addition for a pistol carbine conversion kit
The Micro RONI® is the newest compact addition for a pistol carbine conversion kit. The lightweight and sturdy platform for various Glocks and pistols are made of aluminum with a polymer body. The Micro RONI® features a folding stock for a sturdier position.

- No pistol disassembly required – Just place pistol into the kit and lock
- Equipped with a long top Picatinny rail, allowing a combination of sight, magnifier, and/or night vision
- Provides two extra side Picatinny rails on both right and left for mounting additional accessories
- Ambidextrous, easy and fast handling
- Ambidextrous trigger-guard safety
- Features a right-folding stock for easy concealment and carry
- Right and left serrated thumb-rests for better control on recoil and muzzle-rise* (Not Included)
- Front extra magazine carrier for fast reload
- Front integral tactical light (Not Included)
- Front and rear flip-up sight (Not Incldued)
- Fits only Glock gen’ 3+4 (with bottom picatinny rail), including compensated models (17, 22, 31 OR 19, 23, 32)*

Made Of: Poly+Alum
For Glock
Weight (ounce(s)):1587g, 56oz

MEASURMENTS
Width Max: 63,5mm, 2.5in
Height Max: 190,5mm, 5.7in
Length Max: 348mm, 13.7in


Not compatible with Glock 17 Generation 1 & 2 and Glock 19!

fits for all 2011

fits for all 2011 models

Now you can reload a 1911 Single Stack faster than you ever thought possible. The DP Ice Magwell dominates Action Shooting, and if you shoot a single stack, now you can find out why. The "Replaceable Ice Insert" is fast and forgiving. The super slick insert slides and glides the magazine right in, reducing missed reloads. Time is everything in Action Shooting and a blown reload can cost you a match, so why not have an advantage? The "Ice Advantage". Dawson Precision "KEY LOCKS" the 1911 ICE Magwell to our special checkered Mainspring Housing, both CNC machined to precision tolerances. Grip is solid and improved because of ergonomic design. Easy to install with tools and instructions included. Fits USPSA and IDPA boxes. Get them before the competition does. Available in Silver or Tactical Black. The profile is not too bulky and great for LE, carry or any shooter looking for a "SLICK as ICE" 1911 Single Stack reload. Fits USPSA and IDPA boxes. Legal for USPSA Single Stack Division!  Aluminum Mainspring Housing w/Magwell and Insert Weigh 1.5 oz. Wanna try the No-Gap Ice Magwell? It's as easy as changing the insert! The only difference between the Standard and No-Gap 1911 Ice magwell is the insert!

The Benefit to No Gap - In the past, 1911 magazines were stopped by a tang in front that rested against a relief in the front of the frame. Hey, it's worked for 100 years, but that required magwells to be open in front, to allow the mag to seat fully.
This made the front of the magwell not very forgiving during a speed reload. So we redesigned the whole system. This new insert fills the front gap with a super slick polymer that is "very" forgiving. Now you can have 360 degrees to funnel your 1911 mag into perfect position for consistent, blazing-fast reloads.  All great things come at a price so we had to design a 1911 mag and basepads that exceeded the limits of all conventional design. We took it to a whole 'nother level!

The new mags are DP reliable, of course, and have CNC machined aircraft aluminum base pads, not plastic. We built them to withstand a nuclear blast (although we haven't tested that yet).

Taran Tactical Innovations Competition Magazine Well for 2011 provides the ultimate in reloading performance for your pistol. CNCd from Stainless Steal right here in America, our one-piece push pin design offers premium performance without the irritation of a two piece design. Forward ergonomic relief cuts provide comfort, while a rather large underside funnel to help increases the speed and success of quick reloads. 2.2 ounces of stainless steel provides weight for balance.