Pistolet

New Shadow 2 ultra-short reset disconnector.   After extensive testing, we have engineered a new disco just for the Shadow 2.  This part will drop into most S-2’s and require no fitting, however, due to the timing variations from pistol to pistol, some very slight fitting may be needed on some S-2’s.

The newest compact addition for a pistol carbine conversion kit
The Micro RONI® is the newest compact addition for a pistol carbine conversion kit. The lightweight and sturdy platform for various Glocks and pistols are made of aluminum with a polymer body. The Micro RONI® features a folding stock for a sturdier position.

- No pistol disassembly required – Just place pistol into the kit and lock
- Equipped with a long top Picatinny rail, allowing a combination of sight, magnifier, and/or night vision
- Provides two extra side Picatinny rails on both right and left for mounting additional accessories
- Ambidextrous, easy and fast handling
- Ambidextrous trigger-guard safety
- Features a right-folding stock for easy concealment and carry
- Right and left serrated thumb-rests for better control on recoil and muzzle-rise* (Not Included)
- Front extra magazine carrier for fast reload
- Front integral tactical light (Not Included)
- Front and rear flip-up sight (Not Incldued)
- Fits only Glock gen’ 3+4 (with bottom picatinny rail), including compensated models (17, 22, 31 OR 19, 23, 32)*

Made Of: Poly+Alum
For Glock
Weight (ounce(s)):1587g, 56oz

MEASURMENTS
Width Max: 63,5mm, 2.5in
Height Max: 190,5mm, 5.7in
Length Max: 348mm, 13.7in


Not compatible with Glock 17 Generation 1 & 2 and Glock 19!

Trigger spring CZ 75 TS

fits for all 2011

VIDEO: instructions

Spring and follower upgrade kits for bul SAS II magazines is now available.

9mm 170mm mags 30 rounds capacity reloadable

9mm 140mm maga 24 rounds capacity reloadable

0.40 120mm 19 rounds capacity reloadable

WEB

The Infinity Firearms^® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

• The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
• These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
• Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

• Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
• Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
• Remove the mainspring housing by pulling down.

Attachment Instructions

• Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
• Assemble the gun including the specially machined mainspring housing¹, but do not insert the mainspring housing pin.
• Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
• Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
• Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

¹ - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.

Set includes:

1pcs Striker spring Grey 24N

1pcs Striker spring Red 28N

1pcs Striker spring Blue 31N

1pcs Trigger spring

1pcs Firing pin Safety spring

Ejector spring CZ 75 TS

PMAG GLOCK Magazines

• Compatible with all full-size, compact, and sub-compact 9mm double-stack Glock handguns
• Durable, lightweight, and extremely stiff polymer construction
• High visibility controlled-tilt follower
• Long life stainless steel spring for corrosion resistance
• Flared, easily removable floor plate
• Dot matrix panel for magazine marking and identification
• Magazine indicator windows on both sides of body at 10, 15, and 21 rounds remaining
• Drops free loaded or unloaded

The Next Generation of High Performance Competition Ready Magazines for BUL SAS Styles.

Made from Heat Treated 410 Stainless for Ultimate Durability.

No spacer required for 9mm/.38 magazines.

MBX Complete Tubes were designed to be competition ready with exclusive
features to meet the highest demands for today's shooters.

- All 126mm 9mm/.38 magazines hold 20-21 rounds.

- All 126mm .40/10mm magazines hold 18-19 rounds.

- All 141.25mm 9mm/.38 magazines hold 23-24 rounds.

- All 141.25mm .40/10mm magazines hold 20-21 rounds.

- All 171.25mm 9mm/.38 magazines hold 29-30 rounds.

*Our tubes are designed exclusively to work with MBX Basepads, Springs,
and Followers. These tubes are not designed to work with other manufacturers components.

The tube is designed to work with the MBX Extreme Follower. This is a wider follower with new features that will allow for maximum reliability and capacity.

Witness holes on rear of tube to indicate round count for all tubes.

Kit consisting of

Floating trigger pin, Barrel bushing SP-01, Ultra lite set, Race hammer kit, Sear spacer, Trigger return spring, Hammer pin, Shadow 2 only disconnector. 

Hammer pin retaining peg CZ 75/85

Extractor pin

Sear spring