Country
Select your country here
1) Kreditne kartice
Plačilo s kreditnimi karticami poteka preko plačilnega modula Bankart.
2) Plačilo preko UPN naloga
Plačilo je možno preko nakazila po predračunu (upn nalog):
Banka Intesa Sanpaolo d.d.,
Slovenska cesta 52,
1000 Ljubljana
BIC / Swift Code BAKOSI2XIBO
IBAN SI56 1010 0005 8347 823
Referenca: številka naročila
Dostava
Vaše naročilo bo odpremljeno v enem delovnem dnevu po prejetem plačilu. Pakete odpošiljamo z hitro pošto DPD ali DHL, GLS or Pošta Slovenije. Kupec lahko sam izbira način dobave. Način dostave izbere on zaključku naročila.
Cenik dostave Pošte Slovenije
Standardno pismo
| od 50 g do 100 g | 1,85 eur |
| od 100 g do 250 g | 2,18 eur |
| od 250 g do 500 g | 3,96 eur |
| od 500 g do 1.000 g | 6,54 eur |
| od 1.000 g do 2.000 g | 10,61eur |
Standardni paket
| Do 2 kg | 13,67 eur |
| od 2 kg do 5 kg | 20,48 eur |
| od 5 kg do 10 kg | 25,00eur |
| od 10 kg do 15 kg | 36,11 eur |
| od 15 kg do 20 kg | 41,67 eur |
| od 20 kg do 25 kg | 49,99 eur |
Reklamacije in odstop od naročila
Kupec ima pravico, da v 14 dneh od prevzema blaga pisno sporoči, da odstopa od naročila, ne da bi mu bilo potrebno navesti razlog za svojo odločitev. Šteje se, da je sporočilo pravočasno, če je oddano v roku. Kupec mora najkasneje v 14 dneh po sporočilu o odstopu od naročila podjetniku vrniti blago. Celotne stroške pošiljanja in/ali vračila blaga v primeru vračila krije kupec. Po prejemu blaga in ugotovitvi, da je to nepoškodovano in v nespremenjeni količini. Vračilo opravljenih vplačil bo izvedeno takoj, ko je to mogoče, najkasneje pa v roku 14 dni od prejema sporočila o odstopu od pogodbe. Podjetje vrne prejeta plačila potrošniku z enakim plačilnim sredstvom, kot ga je uporabil potrošnik (kar je najbolj običajno s plačilom na transakcijski račun), razen če je potrošnik izrecno zahteval uporabo drugačnega plačilnega sredstva in če potrošnik zaradi tega ne nosi nobenih stroškov. Kupec ob vračilu blaga pošlje tudi račun za blago in osebne podatke ter transakcijski račun kamor želi, da se vrne plačilo.
Obrazec za odstop od naročila si prenesite tukaj.
When looking to upgrade the performance of a 1911 pistol, a common improvement sought by shooters is a high-quality trigger job, with a crisp, clean break. Until now, a high-quality trigger job has never been in the realm of a “drop-in” upgrade. Nighthawk Custom has changed that with the introduction of our Drop-In Trigger System (DTS) for 1911 pistols. An all-in-one unit, the DTS replaces your existing hammer, hammer strut, sear, disconnector, and sear spring. Your existing sear pin and hammer pin will be retained for use with the DTS, but no other parts are necessary for installation.
With a steel housing securing the unit, the DTS features all Fully Machined™, stainless steel internal components. The traditional three-pronged sear spring is no longer necessary as the springs for the disconnector and sear are built into the unit. A single-leg grip safety spring is included with the DTS to replace the existing sear spring. Never has a high-quality trigger job been this simple for 1911 shooters.
The Drop-In Trigger System is designed for use in most 1911 models, and installation is simple enough that minimal gunsmithing skills are necessary. With a proper safety check and minor gunsmithing skills, our Drop-In Trigger System can give your current 1911 a high-quality trigger job in the time it takes for a routine cleaning of your pistol. Available with stainless or black nitride hammer.
We designed the DTS Trigger System to be approximately 3.5-3.75 lb trigger pull in most applications after the proper break-in period.
Trigger pull may vary slightly from pistol to pistol depending on a variety of factors. We recommend a 500-round break-in period for final results.
*Minor gunsmithing may be required.
FEATURES:
- Anyone can install the DTS. No serious gunsmithing is required.
- You get a clean and crisp, 3.5 - 3.75 lb trigger pull in a matter of minutes.
- There is no sending your pistol off to a custom shop and then waiting 2-3 months to get it back.
- Minimal tools required to complete installation.
- The DTS is easily swapped to a backup pistol in a pinch.
- Installing units in multiple pistols allows identical trigger function in each pistol.
- The DTS is perfect for the home gun builder who can assemble and fit minor parts but isn’t quite comfortable stoning sear and hammer surfaces.
- Average cost for custom trigger job is $380 including shipping
BENEFITS:
- Safe and Reliable
- All internal components are Fully Machined from bar stock 416 stainless steel.
- Offers parallel alignment between the sear and hammer.
- Many stock frames have sear and hammer pin holes that are oversized or not parallel.
- This causes inconsistent results when installing traditional hammers and sears.
- Since the unit is self-contained, the DTS is in control of the critical hammer/sear pivot pin placements and diameters.
- Because Nighthawk is in control of these dimensions, the manufacturer of the frame becomes less of a variable for consistent trigger work.
- Works with 1911 models in Series 70, Series 80, and Swartz Style, as well as 2011 models.
- No bending or tweaking of sear spring legs is necessary to try to tune the pull weight.
- You get a clean and crisp trigger pull.
- Most other trigger kits will have built-in creep due to accommodation of frame manufacturing tolerances.
Sorodni izdelki
© 2020 Cesar Shop