Ajouter des nouveaux élements

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machinesand the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

The DAA Deluxe Magnetic Pouch utilizes two powerful 32mm magnets to hold the magazine securely in place while providing a smoother release than that achieved from the larger standard Magnetic Pouch. The support side walls allow us to use smaller magnets which in turn make the pouches more useable as an all-round pouch for every day use, and not just as a designated pick-up Pouch.

For those shooters who like the simplicity and minimalist look of an open magnetic pouch - this is the perfect choice! The slim body make it possible to position pouches closer together while still leaving enough room to reach down and grab the magazine correctly. The lack of external or front pouch walls allow the pouches to be spaced that much closer together. Perfect for Standard or Production where one must wear the pouches behind the hip bone.

The pouch is attached to our new model belt hanger, which locks securely on any 1.5" belt, clamping down to hold tightly even on thinner belts. The pouch can be swivelled around the centre screw (lower magnet's middle) to angle the pouch as designed. The off-centre mounting point on the hanger offers the option of two heights to choose from. The pouch body is machined from solid Delrin and so is tough and durable. Available in Black only.

Available for Right-Hand users only.

The 2018 Hanger Assembly for the Mr.Bulletfeeder by DAA ships as standard with all new units leaving DAA as of Jan 2018.

Should you wish to upgrade your current hanger assembly (the one with the round Delrin pucks and aluminum rods) you can do so by purchasing this new hanger separately. It is reverse-compatible with all previous Mr.Bulletfeeder by DAA units.

The new hanger is a simplified design, which makes assembly and adjustments to the tilt angle easier and faster to make. The Horizontal aluminum bracket clamps directly onto the motor gear box, allowing for easy assembly on either the left or the right side of the collator, to accommodate your specific position mounting needs.

The vertical piece hangs over the side of your case feeder, and connects to the horizontal bracket by means of a large M8 bolt, which can be loosened and rotated for tilt adjustments.

Sturdy attachment to the collator, a simplified design with fewer parts, thick aluminum profiles and way fewer screws make this hanger simpler and easier to setup and adjust.

Note: Machine NOT included - only Hanger. 

For Shadow 2 and Tactical sport need to be fitted 

The Dropper Assembly is needed for shooters who wish to set up a second tool-head in the same caliber, and wish to quickly transition from, say, 9mm to .38super. Or from one 9mm bullet to another. A change is needed to the collator parts, and if a 2nd tool-head is to be used on the progressive reloader, it is quicker and easier to leave an adjusted Mr.Bulletfeeder dropper on each tool-head. This allows for quick swapovers, without the need to calibrate or adjust the dropper. Note that in most cases you will need to purchase an additional Powder Funnel for your second tool-head’s powder measure, as our expanding powder funnel is required for troublefree reloading.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machines and the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

Many PCC shooters use extended Glock Magazines, often with long base pads added for even more capacity.

To ensure the best possible retention in our Racer and Race Master mag pouches, we are pleased to offer this dedicated extended Glock Side spacer.

Simply assemble this spacer instead of your short one, and allow the bottom of your long mag to extend out the bottom of the pouch body, for a more balanced more secure retention.

The long spacer offers three hole positions in which to place the stopper, giving you the ability to experiment and decide for yourself what the best depth for your magazine is.

NOTE:  this spacer is not compatible with the Alpha-X line of pouches. Magazine and Magazine Pouch not inlucded!

The DAA XL650 Debris-Out Casefeeder Adaptor is the answer to a real problem many reloaders are all too familiar with: when cleaning brass with corncob or other dry media, often small bits of media remain mixed with the brass, and are fed down the case feeder tube. When they reach the tighter diameter of the adaptor tube, they wedge against the cases, causing a feeding jam. You then have to stop reloading, take apart the feeding pipe, clear the jam and only then continue.

But with the new DAA XL650 Debris-Out Casefeeder Adaptor, which replaces the original Dillon case feeder adaptor on your XL650, the slots cut in the pipe allow the debris to fall out the sides onto the small collection tray (we like to keep our workbench clean and neat!) and the chances of a jam-up are greatly reduced.

A drop on fit to your Dillon XL650. 

Not suitable for use on other Dillon reloading models, and cannot be used in conjunction with the DAA XL650 Mini case feeder.

Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.

Some people mark brass to keep up with how many times it has been fired and some people mark their brass so they can later identify brass ownership. We designed Brass Stencils that are specially designed for marking ammo. This stencil is fully compatible with our 100 rnd case gauge. Each stencil set comes with 1 colour marker. You can use any permanent marker that only leaves thin layer if color and does not leave any coat of lacquer that may reduce firearm reliability. Brass Stencils are made from stainless steel and are quick to assemble and easy to apply, the solvent resistant plates can be used again and again.

Kit consisting of

Floating trigger pin, Barrel bushing SP-01, Ultra lite set, Race hammer kit, Sear spacer, Trigger return spring, Hammer pin, Shadow 2 only disconnector. 

Ace's skeletonized stock for the AR-15 rifle. Closed cell foam overtube provides an extremely comfortable cheek weld. Uses A2 buffer tube, rifle length buffer and rifle length buffer spring (NOT INCLUDED). Foam overtube, buttpad and all needed mounting hardware included. Length 10" Weight 11.2oz

Note: Comes only with ARFX Stock and Foam Overtube.  Does not include A2 Extension Tube, Rifle Buffer, Or Rifle Buffer Spring.

This stock uses Ace?s original soft foam overtube for the ultimate cheek weld. A billet machined gusset reinforces the receiver extension tube at its weakest point directly behind the receiver. Precision machined aluminum butt clamps directly to the RET and provides a machined in sling mount.

Note: Comes only with ARFX Stock and Foam Overtube.  Does not include A2 Extension Tube, Rifle Buffer, Or Rifle Buffer Spring.

Seekins Precision, Safety Selector Kit, Red Finish

90 degree standard throw lever

60 degree short throw lever

Available in black or color anodize

Drop in replacement for Mil-Spec selector switch

Fully ambidextrous

Compatible with Ruger Precision Rifle

he Seekins Precision DNA Charging Handle offers a full body and textured grip surface to improve user controls. Our team set out to create a product that would not only offer ergonomic fit and function, but also aesthetic design. Crafted in a climate controlled laboratory by a team of scientists who were only allowed to use their right hands, we can proudly say the DNA handle is the most non-ambidextrous charging handle in our product line up. Really, it's just a charging handle, a very non-ambidextrous one. Enjoy!

Straight single action aluminum trigger with pre-and over-travel adjustment.  All Cajun Gun Works supplied triggers include a 1.5mm allen wrench for your convenience.  This trigger is now a Cajun Gun Works product proudly “Made in the USA”!

TECH TIP:  This is a “conversion” trigger and completely disables the double action feature.  When installing this trigger you will need our TR-PIN as a replacement for the throw away CZ OEM trigger pin, and our SP starter punch for removing the CZ OEM trigger pin.  Remove the disconnector when installing this trigger.  This trigger cannot be used in any CZ decocker.

Full width direct replacement Race hammer and CGW’s exclusive adjustable billet sear.  Produces a competition grade single action pull under 3#’s; not recommended for self defense use.   Will require the use of the CGW S-spacer which is included in the kit.

barrel bushing for the “standard barrel” 9mm manual safety and decocker pistols.  Fits: 75B in 9mm (will not fit the 75B .40, see our 7510X), P-01, PCR, 75B Compact, 85C and 85B.  Made from 4140 and heat treated to RC45.  Reduces barrel muzzle play to -0- at lock-up.  This is a direct replacement for the OEM bushing.  Fits .504” OD CZ’s.  USPSA Production Approved.

NOTE:  Some minor fitting may be required typically at the #46 retaining pin groove.

IDPA Production Legal upgrade kit for the manual safety CZ 75 models.  Fits all “classic” lock work manual safety 75 and 40B, including SP-01.  Everything you need excluding tools.  Our starter punch, part number SP is highly recommended.  Absolutely No Substitutions.

IDPA production legal, full upgrade kit. Includes everything for a 100% compliant competition ready drop-in package for all manual safety 75 series, 75B, 75B Compact, 40B, and SP-01, etc. NOTE: Recommended “Competition” and “Race” gun use only.Produces a 3# or less SA pull weight, not recommended for self-defense use. For all other applications, see our 75100 and 75110 upgrade kits. Absolutely No Substitutions.

Shadow 2 Reach Reduction Kit with ultra-short reset now USPSA Production approved.  Cajun Gun Works’ famous RRK that permanently re-positions the trigger rearward with the hammer fully lowered an amazing 5 mm’s and reduces single action pre-travel dramatically.  Includes our “old style” stainless steel 85C trigger “Made in the USA”  with pre and over-travel screws so you can custom tune to your CZ.

This not only relocates the trigger, but it also doubles as an ultra-short reset for single action.  

Includes 2 different hammer pins (1 x HPIN and 1 x 75009) so you can be assured a secure attachment to either the factory hammer or Cajun Gun Works hammer.  Lifetime warranty to the original purchaser

New Shadow 2 ultra-short reset disconnector.   After extensive testing, we have engineered a new disco just for the Shadow 2.  This part will drop into most S-2’s and require no fitting, however, due to the timing variations from pistol to pistol, some very slight fitting may be needed on some S-2’s.

This ''Follower Kit'' includes: A "Grams Format" follower (CL) & (13coil) spring. For use in CZ "large frame" (Tactical Sport/Checkmate), 9x19 or 40&w magazines, that measure up to 171mm long (with a base pad attached).

A truly ergonomic, shooter focused flat top grip for AR platform rifles and chassis systems. Designed for performance by creating a better interface between the shooter and firearm, the Ergo Grip is still the standard by which positive grip and shooter comfort are measured. The Ergo Grip comes with the patented Gapper™ for increased comfort. Very similar in size to the Original ERGO Grip

Knights Armament Company, Top Rail Rubber Thumb Rest, Fits Picatinny, Black Finish

BUTTSTOCK, PISTOL GRIP(NTG), & M-LOK VERTICAL FOREGRIP COMBO - MIL SPEC +®

BUTTSTOCK

The Daniel Defense adjustable buttstock is constructed of a proprietary blend of glass infused polymers and finished off with soft touch rubber overmolding in strategic points.  The new buttstock is precision formed for mil-spec receiver extensions to have very little forward or lateral play that is so common in many other buttstocks.  This eliminates the need for a tensioning device or friction lock.  All of this results in a durable buttstock that will give the shooter a comfortable and repeatable cheek weld and unprecedented control of the firearm.  The buttstock can be run with one of two included buttpads or without any buttpad at all to custom fit the rifle to whatever gear the operator must wear.  The buttpads come in two sizes: a thicker convex shape (0.8”), and a thinner concave shape (0.5”); designed to keep from snagging when shouldering the rifle.  Limited rotation QD swivel attachment points are integrated on both sides of the buttstock for ambidextrous sling connection.

WEIGHTS AND DIMENSIONS

• 7 Inches Long
• 5.5 Inches Tall
• 1.75 Inches Thick
• Weight: 0.50 lb
• For Mil-Spec receiver extension tubes

PISTOL GRIP

The new Daniel Defense pistol grip is an improvement to the old standby A2.  We designed our grip with ergonomics and controllability in mind.  Our grip shares the angle of the classic 1911 pistol for the most natural hand position and comfortable feel.  This pistol grip incorporates an oversized trigger guard covering the gap between grip and lower receiver which can wear on the shooters hand and easily accommodates for gloves.  Installation is simplified by the fact the integral trigger guard doesn’t require a roll pin so there is a reduced chance of damaging the lower receiver.  A soft touch overmolding section enhances grip, wet or dry.

WEIGHTS AND DIMENSIONS

• 4.25 Inches Tall
• 2 Inches Wide
• 1.38 Inches Thick
• Weight: 0.20 lb

ELF AR-9 Match Trigger 

Product Description

• Fits any mil-spec AR Platform 
• Compatible with Sig MPX which was used extensively in development
• Absolutely Drop-Safe regardless of pull-weight
•  Factory set Pull-weight is approximately 50% lighter than that of a standard AR platform trigger, providing a great combination of speed and accuracy
• Adjustable from 4lbs to 2 3/4lbs without removing from lower
•  Full power hammer spring ensures proper ignition of primer
• Very short pull and reset allows for rapid follow up shots and greater accuracy
•  Sturdy trigger assembly designed for rugged, trouble-free use; Made of lightweight aircraft-grade aluminum and hardened steel
• Unique design of disconnect allows full 1/4” width eliminating possibility of wear and double-firing
• High performance trigger and hammer sealed bearings for smoother and faster firing
• Unique features include captured disconnector eliminating any possible double fires and anti trigger-slap geometry greatly enhancing live fire.
•  100% made in America with a Lifetime Guarantee!

Optimal attenuation
A gunshot is an impulse noise, which is particularly harmful to the human ear. A single shot can cause permanent damage without the proper hearing protection.
Our range of hearing protectors for shooting are specially designed to attenuate, for example, from noise of a gunshot. for reassured protection.

Easy and comfortable
Many shooters have to wear their hearing protectors for a long time. The range of hearing protectors help ensure you’ll have no problems staying focused. The low, two-point fasteners allow an even distribution of pressure over the whole cushion area, to help ensure the ear muff stays in place even during sudden head movements or positioning the weapon. This feature also helps ensure a snug fit without compromising comfort and protection for high quality sound reproduction.

Hear what you want to hear
Our level dependent hearing protectors contain advanced electronics with built-in microphones.
The level dependent ear muffs can amplify external sounds up to four times which enables the shooter to detect faint sounds helping pin-point targets with great accuracy.
Not only are sounds amplified, but they are also reproduced in stereo, allowing you to detect exactly where they are coming from. You become a better hunter when you can hear your dogs and prey from a greater distance. A direct connection to an external communication radio enhances teamwork with your fellow hunters and boosts safety. Some of the products in the level dependent range allow you to adapt the stereo balance, for example if you have a hearing impairment in one ear.

The unique digital sound circuit eliminates the sharp sound clip that is typical for most level dependent hearing protectors on the market. Many people find that sound unpleasant and disturbing.
The new electronics in the PeltorTM SportTacTM hearing protector react instantane- ously, protecting your hearing from loud impulse noises. The system reacts so gently that you rarely hear the clip as the protection is activated.
Just like the other level dependent hearing protectors from 3M, the SportTac hearing protector also enhances your hearing, so you actually hear better with the hearing protector than without it. The PeltorTM SportTacTM also allows you to connect your hunting radio directly to the headset.

• Specially designed for hunters and marksmen
• Smooth active-volume function that helps prevent the sound being cut off abruptly
• Interchangeable shells make it easy to change colours (black and red shells included)
• Automatic shut-off
• Foldable
• Battery life span about 600 hours
• Audio input for an external radio
• SNR26