Ajouter des nouveaux élements

Is there really a difference with Dawson Precision sights? You bet there is! While other sights give off a hazy glow making it difficult to focus, DP sights offer you the sharpest picture. We counterbore the blade so the optic is recessed. This subtle difference focuses the light in the sight making it not only brighter, but clearer. A fully cradled optic provides a longer optic lifespan.

he DAA Output Chute can be attached to any reloading press, hanging onto the same bracket which usually holds the Akro-Bin, and replacing it.

The long, 120cm (4ft) feed spring enables you to run the ammo down to a container on the floor, sparing you the need to empty that bin as you reload, and uncluttering your reloading press.

Some shooters prefer to have a muzzle support on their competition holster. This is an indisputable fact.

While most users will find that the Race Master holster functions perfectly without the additional muzzle support, there are some added advantages to using this extension: The muzzle support prevents the gun from being dislodged upwards, which could happen if bumped on the shooters thigh, or against a prop, during a walkthrough. If the holster was left unlocked, the gun can be dislodged. The muzzle support prevents this from happening.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machinesand the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

The DAA Deluxe Magnetic Pouch utilizes two powerful 32mm magnets to hold the magazine securely in place while providing a smoother release than that achieved from the larger standard Magnetic Pouch. The support side walls allow us to use smaller magnets which in turn make the pouches more useable as an all-round pouch for every day use, and not just as a designated pick-up Pouch.

For those shooters who like the simplicity and minimalist look of an open magnetic pouch - this is the perfect choice! The slim body make it possible to position pouches closer together while still leaving enough room to reach down and grab the magazine correctly. The lack of external or front pouch walls allow the pouches to be spaced that much closer together. Perfect for Standard or Production where one must wear the pouches behind the hip bone.

The pouch is attached to our new model belt hanger, which locks securely on any 1.5" belt, clamping down to hold tightly even on thinner belts. The pouch can be swivelled around the centre screw (lower magnet's middle) to angle the pouch as designed. The off-centre mounting point on the hanger offers the option of two heights to choose from. The pouch body is machined from solid Delrin and so is tough and durable. Available in Black only.

Available for Right-Hand users only.

The 2018 Hanger Assembly for the Mr.Bulletfeeder by DAA ships as standard with all new units leaving DAA as of Jan 2018.

Should you wish to upgrade your current hanger assembly (the one with the round Delrin pucks and aluminum rods) you can do so by purchasing this new hanger separately. It is reverse-compatible with all previous Mr.Bulletfeeder by DAA units.

The new hanger is a simplified design, which makes assembly and adjustments to the tilt angle easier and faster to make. The Horizontal aluminum bracket clamps directly onto the motor gear box, allowing for easy assembly on either the left or the right side of the collator, to accommodate your specific position mounting needs.

The vertical piece hangs over the side of your case feeder, and connects to the horizontal bracket by means of a large M8 bolt, which can be loosened and rotated for tilt adjustments.

Sturdy attachment to the collator, a simplified design with fewer parts, thick aluminum profiles and way fewer screws make this hanger simpler and easier to setup and adjust.

Note: Machine NOT included - only Hanger. 

For Shadow 2 and Tactical sport need to be fitted 

The Dropper Assembly is needed for shooters who wish to set up a second tool-head in the same caliber, and wish to quickly transition from, say, 9mm to .38super. Or from one 9mm bullet to another. A change is needed to the collator parts, and if a 2nd tool-head is to be used on the progressive reloader, it is quicker and easier to leave an adjusted Mr.Bulletfeeder dropper on each tool-head. This allows for quick swapovers, without the need to calibrate or adjust the dropper. Note that in most cases you will need to purchase an additional Powder Funnel for your second tool-head’s powder measure, as our expanding powder funnel is required for troublefree reloading.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machines and the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

Many PCC shooters use extended Glock Magazines, often with long base pads added for even more capacity.

To ensure the best possible retention in our Racer and Race Master mag pouches, we are pleased to offer this dedicated extended Glock Side spacer.

Simply assemble this spacer instead of your short one, and allow the bottom of your long mag to extend out the bottom of the pouch body, for a more balanced more secure retention.

The long spacer offers three hole positions in which to place the stopper, giving you the ability to experiment and decide for yourself what the best depth for your magazine is.

NOTE:  this spacer is not compatible with the Alpha-X line of pouches. Magazine and Magazine Pouch not inlucded!

The DAA XL650 Debris-Out Casefeeder Adaptor is the answer to a real problem many reloaders are all too familiar with: when cleaning brass with corncob or other dry media, often small bits of media remain mixed with the brass, and are fed down the case feeder tube. When they reach the tighter diameter of the adaptor tube, they wedge against the cases, causing a feeding jam. You then have to stop reloading, take apart the feeding pipe, clear the jam and only then continue.

But with the new DAA XL650 Debris-Out Casefeeder Adaptor, which replaces the original Dillon case feeder adaptor on your XL650, the slots cut in the pipe allow the debris to fall out the sides onto the small collection tray (we like to keep our workbench clean and neat!) and the chances of a jam-up are greatly reduced.

A drop on fit to your Dillon XL650. 

Not suitable for use on other Dillon reloading models, and cannot be used in conjunction with the DAA XL650 Mini case feeder.

Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.

Some people mark brass to keep up with how many times it has been fired and some people mark their brass so they can later identify brass ownership. We designed Brass Stencils that are specially designed for marking ammo. This stencil is fully compatible with our 100 rnd case gauge. Each stencil set comes with 1 colour marker. You can use any permanent marker that only leaves thin layer if color and does not leave any coat of lacquer that may reduce firearm reliability. Brass Stencils are made from stainless steel and are quick to assemble and easy to apply, the solvent resistant plates can be used again and again.

Kit consisting of

Floating trigger pin, Barrel bushing SP-01, Ultra lite set, Race hammer kit, Sear spacer, Trigger return spring, Hammer pin, Shadow 2 only disconnector. 

Ace's skeletonized stock for the AR-15 rifle. Closed cell foam overtube provides an extremely comfortable cheek weld. Uses A2 buffer tube, rifle length buffer and rifle length buffer spring (NOT INCLUDED). Foam overtube, buttpad and all needed mounting hardware included. Length 10" Weight 11.2oz

Note: Comes only with ARFX Stock and Foam Overtube.  Does not include A2 Extension Tube, Rifle Buffer, Or Rifle Buffer Spring.

This stock uses Ace?s original soft foam overtube for the ultimate cheek weld. A billet machined gusset reinforces the receiver extension tube at its weakest point directly behind the receiver. Precision machined aluminum butt clamps directly to the RET and provides a machined in sling mount.

Note: Comes only with ARFX Stock and Foam Overtube.  Does not include A2 Extension Tube, Rifle Buffer, Or Rifle Buffer Spring.

Seekins Precision, Safety Selector Kit, Red Finish

90 degree standard throw lever

60 degree short throw lever

Available in black or color anodize

Drop in replacement for Mil-Spec selector switch

Fully ambidextrous

Compatible with Ruger Precision Rifle

he Seekins Precision DNA Charging Handle offers a full body and textured grip surface to improve user controls. Our team set out to create a product that would not only offer ergonomic fit and function, but also aesthetic design. Crafted in a climate controlled laboratory by a team of scientists who were only allowed to use their right hands, we can proudly say the DNA handle is the most non-ambidextrous charging handle in our product line up. Really, it's just a charging handle, a very non-ambidextrous one. Enjoy!

Straight single action aluminum trigger with pre-and over-travel adjustment.  All Cajun Gun Works supplied triggers include a 1.5mm allen wrench for your convenience.  This trigger is now a Cajun Gun Works product proudly “Made in the USA”!

TECH TIP:  This is a “conversion” trigger and completely disables the double action feature.  When installing this trigger you will need our TR-PIN as a replacement for the throw away CZ OEM trigger pin, and our SP starter punch for removing the CZ OEM trigger pin.  Remove the disconnector when installing this trigger.  This trigger cannot be used in any CZ decocker.

Full width direct replacement Race hammer and CGW’s exclusive adjustable billet sear.  Produces a competition grade single action pull under 3#’s; not recommended for self defense use.   Will require the use of the CGW S-spacer which is included in the kit.

barrel bushing for the “standard barrel” 9mm manual safety and decocker pistols.  Fits: 75B in 9mm (will not fit the 75B .40, see our 7510X), P-01, PCR, 75B Compact, 85C and 85B.  Made from 4140 and heat treated to RC45.  Reduces barrel muzzle play to -0- at lock-up.  This is a direct replacement for the OEM bushing.  Fits .504” OD CZ’s.  USPSA Production Approved.

NOTE:  Some minor fitting may be required typically at the #46 retaining pin groove.

IDPA Production Legal upgrade kit for the manual safety CZ 75 models.  Fits all “classic” lock work manual safety 75 and 40B, including SP-01.  Everything you need excluding tools.  Our starter punch, part number SP is highly recommended.  Absolutely No Substitutions.

IDPA production legal, full upgrade kit. Includes everything for a 100% compliant competition ready drop-in package for all manual safety 75 series, 75B, 75B Compact, 40B, and SP-01, etc. NOTE: Recommended “Competition” and “Race” gun use only.Produces a 3# or less SA pull weight, not recommended for self-defense use. For all other applications, see our 75100 and 75110 upgrade kits. Absolutely No Substitutions.

Shadow 2 Reach Reduction Kit with ultra-short reset now USPSA Production approved.  Cajun Gun Works’ famous RRK that permanently re-positions the trigger rearward with the hammer fully lowered an amazing 5 mm’s and reduces single action pre-travel dramatically.  Includes our “old style” stainless steel 85C trigger “Made in the USA”  with pre and over-travel screws so you can custom tune to your CZ.

This not only relocates the trigger, but it also doubles as an ultra-short reset for single action.  

Includes 2 different hammer pins (1 x HPIN and 1 x 75009) so you can be assured a secure attachment to either the factory hammer or Cajun Gun Works hammer.  Lifetime warranty to the original purchaser

New Shadow 2 ultra-short reset disconnector.   After extensive testing, we have engineered a new disco just for the Shadow 2.  This part will drop into most S-2’s and require no fitting, however, due to the timing variations from pistol to pistol, some very slight fitting may be needed on some S-2’s.

This ''Follower Kit'' includes: A "Grams Format" follower (CL) & (13coil) spring. For use in CZ "large frame" (Tactical Sport/Checkmate), 9x19 or 40&w magazines, that measure up to 171mm long (with a base pad attached).

A truly ergonomic, shooter focused flat top grip for AR platform rifles and chassis systems. Designed for performance by creating a better interface between the shooter and firearm, the Ergo Grip is still the standard by which positive grip and shooter comfort are measured. The Ergo Grip comes with the patented Gapper™ for increased comfort. Very similar in size to the Original ERGO Grip

Knights Armament Company, Top Rail Rubber Thumb Rest, Fits Picatinny, Black Finish

BUTTSTOCK, PISTOL GRIP(NTG), & M-LOK VERTICAL FOREGRIP COMBO - MIL SPEC +®

BUTTSTOCK

The Daniel Defense adjustable buttstock is constructed of a proprietary blend of glass infused polymers and finished off with soft touch rubber overmolding in strategic points.  The new buttstock is precision formed for mil-spec receiver extensions to have very little forward or lateral play that is so common in many other buttstocks.  This eliminates the need for a tensioning device or friction lock.  All of this results in a durable buttstock that will give the shooter a comfortable and repeatable cheek weld and unprecedented control of the firearm.  The buttstock can be run with one of two included buttpads or without any buttpad at all to custom fit the rifle to whatever gear the operator must wear.  The buttpads come in two sizes: a thicker convex shape (0.8”), and a thinner concave shape (0.5”); designed to keep from snagging when shouldering the rifle.  Limited rotation QD swivel attachment points are integrated on both sides of the buttstock for ambidextrous sling connection.

WEIGHTS AND DIMENSIONS

• 7 Inches Long
• 5.5 Inches Tall
• 1.75 Inches Thick
• Weight: 0.50 lb
• For Mil-Spec receiver extension tubes

PISTOL GRIP

The new Daniel Defense pistol grip is an improvement to the old standby A2.  We designed our grip with ergonomics and controllability in mind.  Our grip shares the angle of the classic 1911 pistol for the most natural hand position and comfortable feel.  This pistol grip incorporates an oversized trigger guard covering the gap between grip and lower receiver which can wear on the shooters hand and easily accommodates for gloves.  Installation is simplified by the fact the integral trigger guard doesn’t require a roll pin so there is a reduced chance of damaging the lower receiver.  A soft touch overmolding section enhances grip, wet or dry.

WEIGHTS AND DIMENSIONS

• 4.25 Inches Tall
• 2 Inches Wide
• 1.38 Inches Thick
• Weight: 0.20 lb

ELF AR-9 Match Trigger 

Product Description

• Fits any mil-spec AR Platform 
• Compatible with Sig MPX which was used extensively in development
• Absolutely Drop-Safe regardless of pull-weight
•  Factory set Pull-weight is approximately 50% lighter than that of a standard AR platform trigger, providing a great combination of speed and accuracy
• Adjustable from 4lbs to 2 3/4lbs without removing from lower
•  Full power hammer spring ensures proper ignition of primer
• Very short pull and reset allows for rapid follow up shots and greater accuracy
•  Sturdy trigger assembly designed for rugged, trouble-free use; Made of lightweight aircraft-grade aluminum and hardened steel
• Unique design of disconnect allows full 1/4” width eliminating possibility of wear and double-firing
• High performance trigger and hammer sealed bearings for smoother and faster firing
• Unique features include captured disconnector eliminating any possible double fires and anti trigger-slap geometry greatly enhancing live fire.
•  100% made in America with a Lifetime Guarantee!

Optimal attenuation
A gunshot is an impulse noise, which is particularly harmful to the human ear. A single shot can cause permanent damage without the proper hearing protection.
Our range of hearing protectors for shooting are specially designed to attenuate, for example, from noise of a gunshot. for reassured protection.

Easy and comfortable
Many shooters have to wear their hearing protectors for a long time. The range of hearing protectors help ensure you’ll have no problems staying focused. The low, two-point fasteners allow an even distribution of pressure over the whole cushion area, to help ensure the ear muff stays in place even during sudden head movements or positioning the weapon. This feature also helps ensure a snug fit without compromising comfort and protection for high quality sound reproduction.

Hear what you want to hear
Our level dependent hearing protectors contain advanced electronics with built-in microphones.
The level dependent ear muffs can amplify external sounds up to four times which enables the shooter to detect faint sounds helping pin-point targets with great accuracy.
Not only are sounds amplified, but they are also reproduced in stereo, allowing you to detect exactly where they are coming from. You become a better hunter when you can hear your dogs and prey from a greater distance. A direct connection to an external communication radio enhances teamwork with your fellow hunters and boosts safety. Some of the products in the level dependent range allow you to adapt the stereo balance, for example if you have a hearing impairment in one ear.

The unique digital sound circuit eliminates the sharp sound clip that is typical for most level dependent hearing protectors on the market. Many people find that sound unpleasant and disturbing.
The new electronics in the PeltorTM SportTacTM hearing protector react instantane- ously, protecting your hearing from loud impulse noises. The system reacts so gently that you rarely hear the clip as the protection is activated.
Just like the other level dependent hearing protectors from 3M, the SportTac hearing protector also enhances your hearing, so you actually hear better with the hearing protector than without it. The PeltorTM SportTacTM also allows you to connect your hunting radio directly to the headset.

• Specially designed for hunters and marksmen
• Smooth active-volume function that helps prevent the sound being cut off abruptly
• Interchangeable shells make it easy to change colours (black and red shells included)
• Automatic shut-off
• Foldable
• Battery life span about 600 hours
• Audio input for an external radio
• SNR26

A replacement threaded die body for your Mr.Bulletfeeder by DAA Dropper. This threaded body is compatible with all calibers.

The only brush designed with your magazine in mind. Once you own one of these brushes, you will never clean you magazines any other way. One tool to dismantle most magazines and clean them. Making the cleaning easier - which means you will do so more often. And that means you will suffer less malfunctions. Few things are more important to gun reliability than keeping your mags clean! 

The CED Carbon Fiber EVA Pistol Case combines all the great features desired in an EVA a case.  A hard, protective and cool looking shell. Zippered and lockable with a TSA approved combination lock making it ideal for air travel. A handle for easy carry, and dense eggshell foam for complete protection of your valuable pistol.  Will fit one open class or two production pistols. 

How to set your private combination:

1. Make sure the lock is unlocked – default code is 0,0,0
2. Use a toothpick or pen to press down on the small button located on the top of the lock to the right of the locking tabs. A small click sound can be heard.
3. Rotate the dials to your chosen code. A clicking sound will accompany the rotation of the dials
4. Slide the unlocking lever left to set your combination and exit the setting mode. Your new code is now set.
5. You must have the correct code entered in order to use the above mentioned resetting button. Don’t forget your code!

Available in Black Carbon Fiber finish only. 

Dimensions: 32cm x 21cm x 8.5cm (12.8” x 8.4” x 3.4”)

Kit includes: 
- Spring Buffer Pad 
- Custom Buffer Pin 
- Set Screw 
- Allen Wrench 
- 3 Springs: 
   "Red" Standard Power .062
   "Green" Reduced Power .055
   "Blue" Lightest Power .047

Please see recommendations for matching Springs

YELLOW Carbine Spring recommended for most Standard Applications min 115 Power Factor up to 145 Power Factor.

WHITE Carbine Extra Long Spring recommended for 140 Power Factor and Above.

The Lyman QwikDrawTM Barrel Cleaning Rope is a fast, all-in-one cleaning tool that reduces your cleaning time to a fraction of what it would be with a traditional cleaning rod.

Product Details

The Magpul PMAG Ranger Plate is a floorplate replacement for all 7.62x51 PMAG LR/SR GEN M3 magazines that incorporates an integral loop similar to the original Magpul USGI Ranger. When installed on the base of the magazine, the PMAG Ranger Plate provides unsurpassed speed and control during high stress, tactical magazine changes.

Made in U.S.A.

Product Details

Designed as a drop-in upgrade for the standard AR15/M4 pistol grip, The MOE-K Grip provides an extremely low profile and compact design with a steeper grip angle compared to more traditional styles. The more vertical grip angle is optimized for use on PDW (Personal Defense Weapon) configurations and improves comfort and control on short LOP rifles that bring the primary hand in closer to the shooter's body. The thin profile and lack of backstrap 'beavertail' also makes it an excellent choice for shooters who prefer a smaller grip circumference. All mounting hardware included.

Made in U.S.A.

Features

• Replacement for AR15/M4 pistol-grip*
• One-piece reinforced polymer construction
• More vertical grip angle than standard A2 grips
• Minimalist design provides for a compact and thin profile
• Aggressive TSP texture (Trapezoidal Surface Projections) for positive weapon control in all environments

Product Details

Similar in concept to the Magpul Ranger Plate™ for AR15/M16 magazines, the SpeedPlate allows for rapid magazine extraction and positive handling. Protects the base of magazine from impact.

The SpeedPlate replaces the floorplate on all factory Fully Metal Lined (FML) GLOCK 9mm and .40S&W double-stack pistol magazines.*

*NOTE: SpeedPlate is NOT compatible with the Magpul® GL9 series of PMAGs®.

Made in U.S.A.

Product Details

The MS1 Padded Sling is an optimized, dedicated two-point sling that serves equally well in a one-point role when using optional adapters. Built around our MS1 slider, this system provides rapid adjustments to either lengthen or shorten the sling with no slipping once set, and no tails, loops, or other potential snag hazards. In a two-point role, the MS1 allows easy shoulder transitions, rapid adjustability for hands free rifle carry and shooting support from various positions. The MS1 system also has a series of adapters that are sold separately and based on the MS3® and MS4™ slings. By adding the appropriate adapter (available with Paraclip™ or QD Sling Swivel) for the sling, you can easily add one-point functionality to your MS1.

FEATURES

• Dedicated two-point sling with integrated padded section
• Custom variable-width tubular webbing (1-1/4" to 1-7/8") is strong and wear resistant while remaining anti-chafe for user comfort
• High-grade, ripstop coated, closed cell foam pad is sewn to the inside of the sling webbing for protection and strength
• Rapidly adjustable for length (shorter or longer) with new MS1® Slider
• No tails, loops, or other potential snag hazards
• Light weight yet durable hardware made of heavy-duty polymer
• Colored webbing has Near Infrared (NIR) treatment to reduce IR signature
• Can be configured for two to one-point convertibility with optional adapters

Product Details

The BEV Block (Barrel Extension Vise) is an all-in-one, compact vise block tool for AR15/M4 assembly operations of barrel nuts, flash hiders, etc.

Mounts securely in a vise and provides support for both billet and forged upper receivers. Engages barrel extension with solid steel lugs and full length support shank to prevent flexing. Steel hardness is optimized for durability yet won't damage barrel extension, and Magpul Polymer is used for all other engagement surfaces to protect aluminum receiver. O-ring post uses bolt carrier for additional stability and included Pin keeps upper in proper position.

The BEV can also be turned over and used as a mag well vise block to support the lower receiver during maintenance, etc.

Made in U.S.A.

Features

• Provides support for all AR15/M4 upper and lower receivers
• Solidly engages barrel extension with steel lugs
• Full-length steel support shank
• Body made from the same high-quality polymer as other Magpul products

Specs

Specifications

BEV™ Block – AR15/M4

• Weight: 11.2 oz.

Product Details

The PMAG Minus 10 Round Limiter installs in 20 or 30 round GEN M3 PMAG bodies, reducing the magazine capacity by ten rounds. Designed for sporting and hunting applications, installation of the Limiter is simple, tool-less, and requires no permanent modification of the magazine body.

NOTE: Will NOT make a banned magazine legal! This product is intended for TEMPORARY capacity reduction of PMAG AR/M4 GEN M3 magazines. This product does not constitute a permanent capacity reduction. The user is responsible for knowing applicable laws in any jurisdiction that restricts magazines based on capacity or regulates magazine capacity for hunting. Please check all laws and regulations of your state and locality to determine the legality of your host ammunition magazines.

Made in U.S.A.

Product Details

American-made, solid steel construction with grip-enhancing phosphate finish engages both stock and pin-style barrel nuts. Fits standard sized flash hiders. Installs and removes rifle receiver extensions and carbine castle nuts, with extended teeth for use with ASAP plates. Two hammer faces. Works with 1/2" torque wrench, relevant torque specifications included on Wrench for quick reference. Convenient Bottle Opener for refreshments after the build is complete (fits both Metric and SAE bottle caps.)

Made in U.S.A.

Features

• American-made with US steel
• Heat-treated steel construction with manganese phosphate finish
• USGI barrel nut wrench
• Free-float tube barrel nut wrench
• 1/2" torque wrench/breaker bar interface
• Armorer's hammer
• Rifle-length/Entry-length receiver extension wrench
• USGI castle nut wrench*, usable with aftermarket end plates such as the ASAP® and ASAP®-QD
• 3/4" wrench for most flash hiders/muzzle brakes
• USGI torque spec references
• Bottle opener

Specs

Specifications

Armorer's Wrench – AR15/M4

• Weight: 1.1 lb.
• Length, maximum: 11.7 in.
• Handle Thickness: 0.35 in.

NOTE: Not compatible with larger pistol-style receiver extension tubes

JP .223 Enhanced Gas Rings

As a replacement for traditional three-piece gas rings, the JPEGR-223 utilizes a one-piece design similar to the McFarland rings. Unlike the McFarland rings, though, our precision-ground gas rings are engineered to precisely suit small-frame carrier group components such as our own JP EnhancedBolt™.

After testing numerous minute grind callouts, the final JP Enhanced Gas Rings spec is the perfect balance of a solid gas seal with a very low-friction relationship between rings and bolt carrier. Reducing the resistance between these components directly results in an overall increase in the rifle's operational window while the edge of the rings utilizes the cycling action itself to scrape the walls of the carrier, helping shed fouling with every shot.

JP Enhanced Reliability Spring Kit

This spring kit will yield a 3.5-4.0 lb. trigger pull with JP Fire Control parts. This kit is intended for use with JP trigger parts and will not necessarily yield substantial change on standard AR-15 trigger components. 

Application: Use of this spring kit allows for use of ammunition with low-sensitivity primers such as those found in NATO-spec and various foreign-manufactured ammunitions, but in the case of large-frame ARs and duty/defense rifles, domestic-manufactured ammo is strongly recommended to ensure 100% ignition reliability.

The instructors for Magpul's training division wanted a 1911 grip with advanced features, improved control characteristics, and Magpul value. These grips were designed with their input and testing.

Constructed of heavy-duty reinforced polymer, MOE 1911 Grip Panels have a unique diamond-shaped cross section to prevent twisting in the hand, aggressive magazine release cut-out, positive anti-slip texture, and are compatible with ambidextrous safeties. The grips are designed to fit full size framed 1911s with standard grip screw bushings.

Made in U.S.A.

Features

• Fits Full Size Frame 1911s and copies with standard grip screw bushings
• Reinforced polymer construction
• Unique diamond-shaped cross-section to prevent twisting in the hand
• Aggressive magazine release cut-out
• Compatible with ambidextrous safeties
• Positive, anti-slip texture

MBX Offset Scope Mount

The MBX Offset Scope Mount for full size C-More. Designed for fast and easy "heads up" acquisition when installed on a rifle for PCC competition and steel challenge.

Allows for extremely fast and easy visual access of red dot without having to place head over top of butt stock centerline.

Attaches to C-More railway base plate.

Available right or left handed.

-For Right Handed Shooter Choose Right Handed Mount  -For Left Handed Shooter Choose Left Handed Mount

Comes with necessary screws for mounting when used in conjunction with railway mount.

The MBX "Patent Pending" Buffer is Designed specifically for Pistol Carbine Caliber. 

Features an Internal Spring captured within the Buffer to allow for the Buffer/Bolt speed to be significantly reduced during the cycling of the Firearm, resulting in an Extreme Reduction with Felt Recoil.

- Buffer weight 6.8 ozs - Overall length 4.9 inches - Made from Stainless Steel - Includes internal .062 recoil reduction spring - Captured Pin Design to ensure reliability and Performance

2 Adjustable Stoke Lengths: - 1.400 Stroke Long - .900 Stroke Short

In the MBX Buffer tube these parts move at the same velocity as the bolt and run much smoother and silent with a little oil. - Oil the MBX Buffer inside and out - Wipe the main Buffer spring with an oily cloth to add lubrication to the spring - Any medium to light weigh oil is good

Please see recommendations for matching Springs

YELLOW Carbine Spring recommended for most Standard Applications min 115 Power Factor up to 145 Power Factor.

WHITE Carbine Extra Long Spring recommended for 140 Power Factor and Above.

MBX 9mm PCC Compensator "Patent pending"

Designed specifically for competition shooting to achieve the best performance possible with the lower gas volume Pistol Caliber Rifle.

Extra tall port design along with offset side semi circle design for increased surface area. Resulting in highly efficient gas redirection which creates improved downforce and greater stability for the ultimate in dot tracking and follow up shots.

- 20 Deg rear slope port configuration increases compensator forward brake motion to aid in felt recoil.

- Made from T6 aluminum, hard anodized for light weight and durability.

- Includes threaded lock nut for easy installation and 6/32 tapped set screw to aid in installation or pinning if required.

- 3" overall length, .875 wide & 1 1/4" tall

- Available threads: 1/2 x 28 & 1/2 x 36

- Weight: 2.4oz

Mil-spec 6-position buffer tube manufactured from 7075 aluminum with black anodized finish.

Tube only; endplate and castle nut not included