Añadir articulo(s)

GHOST BLOCK

• Locks the firearm and prevents unauthorized use.
• It’s always with the firearm.
• Cannot be illegally deactivated without permanently disabling the weapon.
• No lock combinations to fumble with.
• Does not alter the function or reliability of the firearm.
• Instant visual determination of the locked or unlocked condition.
• Non-destructive design means no permanent changes to the firearm.

Paddle belt can be used with the CARBON GHOST BELT to obtain better extraction. Also gives better stability of the holster thanks to the rigid higher part.

The Ghost Ultimate Vest is made from a PolyStrecth shell which adjusts to every kind of movement giving you unlimited freedom to move without being hindered by fabric.

• extremely light
• water and wind resistant
• great isolation properties keeps the warmth in and the cold out
• internal liner is made from a highly moist repellent netting.
• shoulder pieces made from non-slip Metal Cordura for the butt stocks of rifles
• PolyAmide stretch side inserts keeps the Shell Vest close to the body for unobstructed access to the weapon and pouches
• 2 watertight zippered pouches
• 2 pouches for mags (one pistol, one rifles) to carry the first mag to the start position without taking up any mag pouch space
• Round Velcro Ghost Patch for your teams personal tag.

WEB

The Infinity Firearms^® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

• The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
• These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
• Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

• Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
• Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
• Remove the mainspring housing by pulling down.

Attachment Instructions

• Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
• Assemble the gun including the specially machined mainspring housing¹, but do not insert the mainspring housing pin.
• Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
• Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
• Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

¹ - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.

WEB

The Infinity Firearms^® Magazine well available for traditional single stack 1911 pattern guns demonstrates that it is possible to build a better mousetrap.

This magazine well attaches to the firearm by means of a specially machined mainspring housing. The lower front portion of the mainspring housing is machined to allow a projection from the magazine well to interlock around the mainspring housing retaining pin.

Two specially designed bolts "snug up" the mainspring housing are fully captive, which provides a few benefits:

• The magazine well will remain in place even if these bolts are loosened. The bolts serve to "snug up" the magazine well so there is absolutely no possibility of movement, but do not need to be tightened to hold the mag well in place.
• These bolts cannot be lost. They are captive, and can only be removed after the magazine well has been removed from the gun.
• Appearance - the "snake eye" holes used for Allen wrench access to these bolts are much smaller in diameter than the bolts.

Removal Instructions

• Insert a 1/16" Allen wrench into each of the snake eye holes, and rotate at least 1/2 turn clockwise. These retaining bolts have a narrow non-threaded section in the middle which bears against the mainspring housing pin when the bolts are rotated counterclockwise. The key here is that you are not "unscrewing" two parts, but shifting an interlocking "key" away from the pin upon which it bears.
• Drive the mainspring housing out of the gun, by inserting a drift punch into the dimpled end of this pin.
• Remove the mainspring housing by pulling down.

Attachment Instructions

• Since this magazine well overlaps the grips, the grips must be installed before the magazine well.
• Assemble the gun including the specially machined mainspring housing¹, but do not insert the mainspring housing pin.
• Make sure the two bolts are captive in the magazine well, and adjusted so the mainspring housing retaining pin can move freely without bringing on the bolts. (refer to the top left figure on this page for an example of the proper orientation).
• Remove the mainspring retaining pin from the magazine well, and place the magazine well on the gun.
• Insert the mainspring retaining pin, and use a 1/16" Allen wrench in each of the "snake eye" holes to rotate the bolts counter clockwise until they are snug.

¹ - This write up assumes that the reader is already familiar with the procedure for installing the mainspring into the mainspring housing prior to assembly. If you are simply removing and then re-installing an existing Infinity® Traditional Single Stack Magazine Well, the mainspring housing will already contain the mainspring. If you are installing a new mainspring housing, and need to install the mainspring, please consult a reference on 1911 gunsmithing, and re-read the note at the top about eye protection before proceeding.

L.C.S. – Left Charging System –

CALIBRE : 223 

LENGHT : 18” (Cal.223)  

TWIST RATE :  1/9 (Cal.223)  

UPPER: CNC Machined from our design billet – AL 7075T6 in H170 Titanium Cerakote

MIL SPEC compatibility and M4 Feed ramps Without forward assist

Charging Handle with Tactical Latch Oversize Ambi

LOWER: CNC Machined from our design billet – AL 7075T6in H170 Titanium Cerakote 

MIL SPEC  compatibility

Enhanced flared/magwell magazine

Integral trigger guard, great for gloves use

Ambi selector

Mag. release oversize

Ambi bolt catch Anti rotation trigger pin                                        

Made stronger than other similar commercially

BARREL: Hammer forged nitrited – Heavy profile – thread: 1/2 X 28 with compensator.

GAS SYSTEM: Direct gas impingement with gas block low profile.

BOLT CARRIER GROUP: Stainless Steel with QPQ treatment antifriction – black.

HANDGUARD: Octagonal free float slim with four frontal picatinny – original design – CNC machined – M-LOK System – full size barrel.

TRIGGER: U.L.T.R.A. adjustable – 2,5Lb

STOCK: Tube MIL SPEC collapsible.

Info: Left Charging System, reciprocating steel charging handle, attached to a modified carrier and upper receiver. Facilitates the Charging operation without leaving the line of sight, designed for use both competitive and tactical. Made after careful ergonomic studies and extensive field trials.

3GUN 

with M-LOK HANDGUARD in H152 Stainless Cerakote  

CALIBRE : 223

• LENGHT :   18” – 20”

• TWIST RATE :  1/9

• UPPER: Forged and machined from our design billet – AL7075T6

Hard black anodized

MIL-SPEC and M4 Feed ramps

Charging handle with tactical latch Ambi Oversize

Made stronger than other similar commercial rifles                                                                                     

• LOWER: Forged and machined from our design billet – AL7075T6

Hard black anodized

Enhanced flared/Magwell magazine

Integral trigger guard

Mag. release OVS

Bolt catch OVS

Selector Ambi 45° 

Made stronger than other similar commercial rifles

• BARREL: Lothar Walther – 3GUN profile – thread: 1/2×28 with Sport compensator

• GAS SYSTEM: Direct gas impingement with gas block low profile adjustable

• BOLT CARRIER GROUP: Stainless Stell – Lightweight with QPQ Treatment Antifriction – Black

• HANDGUARD: CNC machined, free floated  Ventilated, M-LOK H152 Stainless Cerakote   

Possibility to regulate the gas block from outside without remove the handguard

• TRIGGER: MIL SPEC with lightweight springs

• STOCK: Fixed competition