Select your country here
Please select your country
Корзина пуста
По этим критериям поиска ничего не найдено
MBX 9mm PCC Compensator "Patent pending"
Designed specifically for competition shooting to achieve the best performance possible with the lower gas volume Pistol Caliber Rifle.
Extra tall port design along with offset side semi circle design for increased surface area. Resulting in highly efficient gas redirection which creates improved downforce and greater stability for the ultimate in dot tracking and follow up shots.
- 20 Deg rear slope port configuration increases compensator forward brake motion to aid in felt recoil.
- Made from T6 aluminum, hard anodized for light weight and durability.
- Includes threaded lock nut for easy installation and 6/32 tapped set screw to aid in installation or pinning if required.
- 3" overall length, .875 wide & 1 1/4" tall
- Available threads: 1/2 x 28 & 1/2 x 36
- Weight: 2.4oz
The MBX "Patent Pending" Buffer is Designed specifically for Pistol Carbine Caliber.
Features an Internal Spring captured within the Buffer to allow for the Buffer/Bolt speed to be significantly reduced during the cycling of the Firearm, resulting in an Extreme Reduction with Felt Recoil.
- Buffer weight 6.8 ozs - Overall length 4.9 inches - Made from Stainless Steel - Includes internal .062 recoil reduction spring - Captured Pin Design to ensure reliability and Performance
2 Adjustable Stoke Lengths: - 1.400 Stroke Long - .900 Stroke Short
In the MBX Buffer tube these parts move at the same velocity as the bolt and run much smoother and silent with a little oil. - Oil the MBX Buffer inside and out - Wipe the main Buffer spring with an oily cloth to add lubrication to the spring - Any medium to light weigh oil is good
Please see recommendations for matching Springs
YELLOW Carbine Spring recommended for most Standard Applications min 115 Power Factor up to 145 Power Factor.
WHITE Carbine Extra Long Spring recommended for 140 Power Factor and Above.
The Next Generation of High Performance Competition Ready Magazines for BUL SAS Styles.
Made from Heat Treated 410 Stainless for Ultimate Durability.
No spacer required for 9mm/.38 magazines.
MBX Complete Tubes were designed to be competition ready with exclusive features to meet the highest demands for today's shooters.
- All 126mm 9mm/.38 magazines hold 20-21 rounds.
- All 126mm .40/10mm magazines hold 18-19 rounds.
- All 141.25mm 9mm/.38 magazines hold 23-24 rounds.
- All 141.25mm .40/10mm magazines hold 20-21 rounds.
- All 171.25mm 9mm/.38 magazines hold 29-30 rounds.
*Our tubes are designed exclusively to work with MBX Basepads, Springs, and Followers. These tubes are not designed to work with other manufacturers components.
The tube is designed to work with the MBX Extreme Follower. This is a wider follower with new features that will allow for maximum reliability and capacity.
Witness holes on rear of tube to indicate round count for all tubes.
MBX "Fang" CTR & Hogue Stock Extensions
For installation on the Magpul model CTR, this extends the factory Butt Stock to allow for deeper and more stable contact with the shoulder pocket allowing for greater recoil control and added stability when reloading along with a raise stance when used in conjunction with the MBX off set mount.
A 5 piece Delron stroker kit consisting of a long and medium main contact shim & stack shims .100-.200-.300 to allow multiple combinations of stroke length allowing you to tune your preference in trigger load and cycle speed. For 9mm AR
Kit includes: - Spring Buffer Pad - Custom Buffer Pin - Set Screw - Allen Wrench - 3 Springs: "Red" Standard Power .062 "Green" Reduced Power .055 "Blue" Lightest Power .047
MBX Super Lightweight Barrel weighs Only 12.5oz by itself, after we install our MBX Compensator and we have produced an ALL Stainless 1lb PCC Barrel that comes in at 16.1 inches for Legal Length.
MBX Offset Scope Mount
The MBX Offset Scope Mount for full size C-More. Designed for fast and easy "heads up" acquisition when installed on a rifle for PCC competition and steel challenge.
Allows for extremely fast and easy visual access of red dot without having to place head over top of butt stock centerline.
Attaches to C-More railway base plate.
Available right or left handed.
-For Right Handed Shooter Choose Right Handed Mount -For Left Handed Shooter Choose Left Handed Mount
Comes with necessary screws for mounting when used in conjunction with railway mount.
MBX "Mega" PCC 6" Competition Extension Basepad with MBX Custom Spring
Adds Maximum capacity up to 57 rounds
For Factory Glock 9mm and ETS Magazines only.
Includes: - MBX 6" Mega Extension Basepad - MBX 28 Coil Custom Spring
MBX "Mini" PCC Competition 4" Extension Basepad with MBX Custom Spring
Adds Maximum capacity up to 47
Includes: - MBX 4" Mini Extension Basepad - MBX 24 Coil Custom Spring
MBX Z-Max 11 Coil Spring & Competition Follower Set for 140mm & 126mm MBX STI/SVI style tubes
Next Generation of High Performance Competition Ready Magazines for STI/SVI 2011 Styles.
MBX Complete Tubes were designed to be competition ready with exclusivefeatures to meet the highest demands for today's shooters.
*Our tubes are designed exclusively to work with MBX Basepads, Springs,and Followers. These tubes are not designed to work with other manufacturers components.
