Ausrüstung zum Wiederladen

The ultimate in convenience for keeping your reloading bench clean and uncluttered. You will find in an instant what you need to make the switch from one to another caliber.  

This stand is for the RL550 Series and XL650 machines only.

These lighter weight Aluminum toolheads are machined from billet using the same precise CNC machining as our standard toolheads. Available in four different colors to allow you to quickly differentiate between calibers or load types.

Primer cam Index Stop Switch for Dillon Precision XL-650 and SL-900 Progressive Reloading Press. The switch moves to turn ON and OFF the index by bypassing the indexing lever on the primer feed assembly. Integrated spring ball works as clickable position capture. Use the factory screw to install. Material for the base is 6082 aluminium and material for the ramp is Delrin (POM-C). Spare ramps can be ordered separately. Super simple install. Just unscrew original primer cam and use same bolt to attach this stop switch.

Powder Baffle is a must have reloading accessory that dramatically increases powder load consistency and accuracy! 

When reloading your own ammunition it is common to produce 500 to 1,000 rounds per hour. At this rate your powder reservoir empties pretty fast. The weight of powder in the tube affects how full of a charge your bullets receive. A baffle ensures consistent weight on the powder at the bottom of the reservoir, giving you consistent loads.

This design eliminates direct weight from the powder in the powder tube reservoir to the charge bar allowing the most consistent and accurate flows. Whether the powder reservoir tube is full, half way or almost empty your averageload should be consistent. 

Powder Baffle is made from stainless steel.

Fits on Dillon Auto Powder Measure . It only takes a few seconds to drop it down into the bottom of the Dillon powder hopper. The powder hopper is not modified and your Dillon Warranty will not be effected.

Mistakes happen, so be prepared. Our hammer-style Bullet Puller quickly removes your bullets without damaging the bullet or the case. The rubberized grip is easy on your hands and we have also added a rubber insert inside the hammer tip to make it easy on your bullets. Easy and convenient to use whether checking an occasional  reload or pulling hundreds of bullets.

This Hammer Set comes with 4 collets.

LIFETIME WARRANTY.  MADE IN THE USA.

Collet information:
                                        Pistol                                      Rifle
Black (X-Small) -    .25 ACP                        Small Rifle Calibers
Blue (Small) -           .32 - .380                      17 Rem - 223 Rem
Green (Large) -       9mm - 10mm                       6mm - 8mm    
Red (X-Large) -      .41 - .45 ACP                  Belted Mags - 45-70

13940 for XL650/1050 or 13940 SQD for square deal machines.

13940 is only the aluminium body. 

Part number 21275 is 13940 for 650/1050 with added screws and inner sleeve

21275 has all parts added to be the complete Body collar for XL650/1050.

The polymer nylon inner sleeve that is mostly needed together with the Aluminium body is 13845.

https://cesar-shop.com/product...

Carbide sizing die 9MM Luger Carbide Full Length only. No case lube needed.

Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.

The Dillon RL 1050 Cartridge Bin is used on the Super 1050 progressive reloading machine to catch the loaded cartridges. This bin is 260mm long, 110mm wide by 120mm deep and is great for storing just about anything.

Dillon's blue AkroBins are made of virtually unbreakable heavy-duty polypropylene. They're unaffected by weak acids and alkalis and are also water, rust and corrosion proof. They are great for reloaders requiring extra capacity, or those loading several calibers, bullet weights, bullet shapes, etc. AkroBins can be used for storing almost anything!

Collar sleeve Sqare deal B

A common question we hear is “Can I use the Bullet Feeder on my 550?” Or “Can I use the Bullet Feeder and still continue to use my powder check on my 650?”.

Such Seating and Crimping dies are available, and so we decided it was time we made them directly available to our customers as well. LEE Precision produces these, so no question about the quality. 

The 2-in-1 Seating and crimping die include an O-ring lock machined into the nut, which allows you to hand tighten only – and the die stays put! They include a finger adjustable floating bullet seater. For durability they are heat treated to ideal hardness and polished to the smoothest finish.

The DAA Bullet Puller is a must-have for serious reloaders. This tool takes all the hassle out of separating your used cases from the bullet and powder. The tool itself is formed from high-quality plastic with an aluminum rod to ensure many years of durable performance.

The DAA Bullet Puller can be used for ammunition of all sizes ranging from .17 Remington to .50/70 Government cases. This tool comes with an extra set of three collets, should the originals happen to break. The tool itself is virtually indestructible and makes quick work of disassembling your ammunition for reloading.

he DAA Output Chute can be attached to any reloading press, hanging onto the same bracket which usually holds the Akro-Bin, and replacing it.

The long, 120cm (4ft) feed spring enables you to run the ammo down to a container on the floor, sparing you the need to empty that bin as you reload, and uncluttering your reloading press.

The DAA Powder-Spill-Prevention (PSP) Brush is a simple yet efficient reloading accessory that solves a real issue: How to prevent small amounts of powder being spilled out of the case, as the tool head of the progressive reloading press indexes?

The DAA Powder-Spill-Prevention (PSP) Brush is a simple yet efficient reloading accessory that solves a real issue: How to prevent small amounts of powder being spilled out of the case, as the tool head of the progressive reloading press indexes?

The DAA XL650 Debris-Out Casefeeder Adaptor is the answer to a real problem many reloaders are all too familiar with: when cleaning brass with corncob or other dry media, often small bits of media remain mixed with the brass, and are fed down the case feeder tube. When they reach the tighter diameter of the adaptor tube, they wedge against the cases, causing a feeding jam. You then have to stop reloading, take apart the feeding pipe, clear the jam and only then continue.

But with the new DAA XL650 Debris-Out Casefeeder Adaptor, which replaces the original Dillon case feeder adaptor on your XL650, the slots cut in the pipe allow the debris to fall out the sides onto the small collection tray (we like to keep our workbench clean and neat!) and the chances of a jam-up are greatly reduced.

A drop on fit to your Dillon XL650. 

Not suitable for use on other Dillon reloading models, and cannot be used in conjunction with the DAA XL650 Mini case feeder.

Sizing/Depriming Die 
Our sizing/depriming dies feature a unique "floating decap assembly" with a snap spring that throws the spent primer off the pin and eliminates the problem of primer "draw back" that often occurs when decapping military brass. The primary feature of Dillon's size die design the long, tapered carbide ring with a radiused opening remains unchanged. 
That radiused opening, and its importance to progressive reloading, is one of the reasons why our seat and crimp dies are better. We found a way of manufacturing these dies that has enabled us to make the lead-in radius even bigger! The bigger radius makes progressive loading with our equipment even smoother but that's still only a part of the story. 

Lee Replacement decapping pin for Decapping Die (#90292)

This heavy-duty nylon cover comes equipped with a D-ring, allowing the zipper to be locked. 

If you have a Mr. Bulletfeeder mounted onto your 1050, this cover will still cover the machine, but you must orient the cover so that the zipper is on the LEFT side, not the back. 

Sizing/Depriming Die
Our sizing/depriming dies feature a unique “floating decap assembly” with a snap spring that throws the spent primer off the pin and eliminates the problem of primer “draw back” that often occurs when decapping military brass. The primary feature of Dillon’s size die design the long, tapered carbide ring with a radiused opening remains unchanged. That radiused opening, and its importance to progressive reloading, is one of the reasons why our seat and crimp dies are better. We found a way of manufacturing these dies that has enabled us to make the lead-in radius even bigger! The bigger radius makes progressive loading with our equipment even smoother but that’s still only a part of the story.

Bullet Seating Die
Our new quick-disassembly seat die allows the user to disassemble and clean the seat die without losing adjustment. In this manner, bullet lube and shavings can be quickly removed from the die, thereby guaranteeing a constant seating depth. We’ve incorporated a “flip-flop” seating stem and a clip that enables you to remove the die insert and change the seating stem from round nose to semi-wadcutter without unscrewing a seating stem out of the die body. We’ve always included both types of seating stems, but the new double-ended design makes it a simple matter to remove a pin, reverse the seating stem, make any minor seating depth adjustments that may be necessary and go on loading in a fraction of the time it used to take.

Crimp Die
We’ve made it easy for you to remove the die insert for cleaning without having to change the critical crimp adjustment. Once your crimp die is set for the proper amount of crimp, you’ll never have to change it. This is especially good news for all of you who load lead bullets! Before, you had to unscrew the die from the toolhead and disassemble the die in order to remove any bullet lube or lead residue. Then, you had to start from square one to re-adjust the crimp. Those days are over. All you have to do now is pop a clip and the die insert drops into your hand for cleaning.

NOTE: All Dillon Pistol Die sets include our sizer/ decap die, seat die and a separate crimp die. (Taper crimp for autos; accu-crimp for revolvers.)

The secret of really punching out a lot of rounds in a hurry. Have these tubes filled and ready to go. There are tubes for small diameter primers and large diameter primers.

Electric Case Feed System allows you to simply dump fired, cleaned and deprimed hulls into the bowl.  The Case Feeder orients the hulls right side up and fills the feed tube automatically, turning itself on and off as necessary, to keep the case feed tube full.

The Casefeeder will hold 600 .38 Special cases or 500 .223 Rem cases. 

Be aware this casefeeder is without the Case feeder plate that is appropriate for the type of ammunition you wish to reload. See here the Case feeder plate you need. 

What the Free-Float, Zero-Play Toolhead do?
This toolhead has lock rings that allow the sizer and seater dies to float. This floating action allows the dies to center themselves exactly over each cartridge for the best possible alignment and more concentric ammunition.

What is Zero Play? This toolhead does not use original toolhead pins supplied by dillon. This toolhed is bolted with two M3 bolts and lifts toolhead into upmost position. When you cycle cases downwards toolhead does not move and cases go out in straght line. Best practice is to loosen M3 bolts a little bit and push index shell-plate with case in to dies and tighten M3 bolts in toolhed best position.

What is concentricity and what does it matter? Concentricity refers to how straight the bullet is on top of the loaded round. A bullet that is straight will enter the rifling in the barrel that way. Bullets that enter the rifling slightly crooked do not shoot with their highest accuracy.

What’s wrong with using the OEM toolheads? The Dillon presses are great machines made to high quality standards. However, the cast toolheads have limitations. How do we know if the toolhead flange is flat? Or how do we know that each threaded station in the toolhead is in perfect alignment with the shellplate? How do we know that the stations are equally spaced? All of these areas compound for possible misalignments and lead to ammunition that isn’t quite as concentric as it could be. The toolhead is the final link between your dies and your press so it only makes sense that quality is extremely important. With over 100,00 EUR of dies, powder measure, and other accessories mounted in your toolhead, don’t you want to know it’s the best available!

What is different about the new CNC Machined Toolhead? These toolheads are made to the highest standards. The are CNC machined from 6082 aluminum, which is much stronger and has less flex than a cast toolhead. All critical dimensions are machined in a single operation, ensuring that all surfaces are true and aligned relative to each-other. The die holes are positioned with a very high degree of accuracy and the 7/8-14 threads are machined to tight tolerances for  precise fit and alignment, yielding dies that are more precisely centered in each hole and better aligned to the cartridge cases in the shellplate. The flange is also flatter than can be achieved with a cast toolhead.

• Made in Europe
• Include M3 bolts and hex key.
• Ready for Free-float rings.

Free-float rings are sold seperately. Usually you need two free-float rings. One for resize and other for bullet seating. However you can add free-float ring to each station.

Comes with powder check die and 3 check rods which are from .22 till .45 Cal. Battery AAA is included.

This item does not check the accuracy of the powder charge, it checks for double-charges or no-charges only.

This mount is for both the RL 550 series presses as well as the XL650.  Mount height = 8 1/2"  or 21,6 centimeters.

Raises your press above the work bench level and adds stability due to its larger footprint.

Recommended by lots of reloaders.

Mounts directly to Strong Mount. Fits the Square Deal, RL550 series and XL650 strong mounts. For 1050 machines use #22215. You must have a strongmount in order to use this bullet tray.

Dillon's accessory handle gives your reloader an entirely new "feel." 
A roller handle reduces operator fatigue during long reloading sessions and makes primer seating easier. Fits the RL550 and XL650 loaders. 

Small Pistol .32, .380, 9mm, .38 Super, .30 Carbine

Large Pistol .40 S&W, 10 mm, .38 Special and larger, 7.62 x 39

Small Rifle .204 Ruger, .222, .223 Remington

Large Rifle .22-250 and larger

The Dillon Magnum Rifle Powder bar throws charge weights from 50 grains up to approximately 72 grains of extruded powder, or up to approximately 82 grains of ball/spherical powder