Перезаряжающее оборудование

Spent primer catcher pin #13998

The Dillon RL550C is the most versatile reloading machine in the Dillon Precision Products line.  It will accommodate the widest variety of cartridges from 32 ACP up to 338 Lapua, 416 Rigby, and 460 Weatherby.

The RL550 has a manually indexed shellplate making it easier to master the various steps of reloading. Manual indexing also gives the operator greater control over each individual step in the loading process. Caliber changes are simple and require fewer parts than other machines which makes it less expensive to convert to another cartridge.

Reloading with Dillon’s RL 550 is Easy as 1-2-3!

Most shooters realize that reloading is the most economical way to enjoy their sport, but many shooters are unaware of just how simple it is to reload. In fact, Dillon’s RL 550C is the easiest progressive loader in the world to learn to reload with. How can we make that statement? Simple. Since all of the reloading steps are performed with a stroke of the handle, there is less to remember (or forget) than with an old-fashioned single-station press.

No dies are included with the RL550!

Electric Case Feed System allows you to simply dump fired, cleaned and deprimed hulls into the bowl.  The Case Feeder orients the hulls right side up and fills the feed tube automatically, turning itself on and off as necessary, to keep the case feed tube full.

The Casefeeder will hold 600 .38 Special cases or 500 .223 Rem cases. 

Be aware this casefeeder is without the Case feeder plate that is appropriate for the type of ammunition you wish to reload. See here the Case feeder plate you need. 

Powder measure knob for the Dillon Powder thrower with click for easy adjustment.

Unlike other competitors, this knob is laser etched with 50 graduations giving the user reference points when adjusting. Two steel spring loaded balls generate smooth and repetable clicks. Easy to setup between multiple loads or even calibres, very precise 50 clicks per turn. Testing on pistol powders one click increments is about 0.015 grains. This is a very precise setting. 

Simple installment and a tremendous help for if you are using different loads with visual scale.

The Dillon Factory screw requires a wrench when adjusting the amount of powder to dispense in your powder thrower. This knob is labeled with graduations for orientation and easily allows the user to hand adjust the powder dispenser without the need for tools. Works on Dillon 1050, 650,550, SDB and 900 presses.

Both parts are made from aircraft grade aluminum - anodized black color

1 x laser etched knob assembly consisting of one knob frame and one adjusting knob

1 x allen wrench for the grub-screws to fasten

Dillon Powder Bar shown only for reference and is NOT included.

Sizing/Depriming Die
Our sizing/depriming dies feature a unique “floating decap assembly” with a snap spring that throws the spent primer off the pin and eliminates the problem of primer “draw back” that often occurs when decapping military brass. The primary feature of Dillon’s size die design the long, tapered carbide ring with a radiused opening remains unchanged. That radiused opening, and its importance to progressive reloading, is one of the reasons why our seat and crimp dies are better. We found a way of manufacturing these dies that has enabled us to make the lead-in radius even bigger! The bigger radius makes progressive loading with our equipment even smoother but that’s still only a part of the story.

Bullet Seating Die
Our new quick-disassembly seat die allows the user to disassemble and clean the seat die without losing adjustment. In this manner, bullet lube and shavings can be quickly removed from the die, thereby guaranteeing a constant seating depth. We’ve incorporated a “flip-flop” seating stem and a clip that enables you to remove the die insert and change the seating stem from round nose to semi-wadcutter without unscrewing a seating stem out of the die body. We’ve always included both types of seating stems, but the new double-ended design makes it a simple matter to remove a pin, reverse the seating stem, make any minor seating depth adjustments that may be necessary and go on loading in a fraction of the time it used to take.

Crimp Die
We’ve made it easy for you to remove the die insert for cleaning without having to change the critical crimp adjustment. Once your crimp die is set for the proper amount of crimp, you’ll never have to change it. This is especially good news for all of you who load lead bullets! Before, you had to unscrew the die from the toolhead and disassemble the die in order to remove any bullet lube or lead residue. Then, you had to start from square one to re-adjust the crimp. Those days are over. All you have to do now is pop a clip and the die insert drops into your hand for cleaning.

NOTE: All Dillon Pistol Die sets include our sizer/ decap die, seat die and a separate crimp die. (Taper crimp for autos; accu-crimp for revolvers.)

he DAA Output Chute can be attached to any reloading press, hanging onto the same bracket which usually holds the Akro-Bin, and replacing it.

The long, 120cm (4ft) feed spring enables you to run the ammo down to a container on the floor, sparing you the need to empty that bin as you reload, and uncluttering your reloading press.

The DAA Bullet Puller is a must-have for serious reloaders. This tool takes all the hassle out of separating your used cases from the bullet and powder. The tool itself is formed from high-quality plastic with an aluminum rod to ensure many years of durable performance.

The DAA Bullet Puller can be used for ammunition of all sizes ranging from .17 Remington to .50/70 Government cases. This tool comes with an extra set of three collets, should the originals happen to break. The tool itself is virtually indestructible and makes quick work of disassembling your ammunition for reloading.

Mark 7® 650 PRO Autodrive

Differentiating Features  

• Includes the Mark 7 Optical Decapping Sensor - a $200 value !
• Completely compatible with Mr. Bulletfeeder and GSI bulletfeeders
• Broad caliber capacity - able to load a wider array of calibers including larger rifle calibers
• Small footprint
• Digital clutch - adjustable on-the-fly from 0 to 20
• Digital primer depth setting - no more guessing !
• Digital jog and immediate stop
• Microprocessor monitored and controlled
• Includes pre-loaded computer tablet - no control boxes!
• Features monitored by computer
• Downloadable software upgrades for life
• Supports a variety of accessories
• User-configurable Dwell time at the top of the stroke as well as the bottom
• Easy Installation
• Pre-assembled and shipped ready to use
• CNC grade planetary gearbox
• Full warranty
• High torque motor - same available torque to machine as the 1050 X Autodrive
• Fully Supports International Voltage - this unit operates at 110/220v and at 50/60 Hz with no appreciable variation in speed or performance

Dimensions and Capacity

• Overall machine dimensions are 49" tall (124.4 cm) X 14" (35.5cm) wide x 12" (30.5cm) deep x 1/2" (1.27cm) thick
• True operational height: earlier machines 52.5", later machines 48.5"
• User selectable speeds from 900 to 1,800 rounds per hour
• Quite operation approximately at 75-80 dB including case and bullet feeder

650 Autodrive Specifics

• CNC billet heavy-duty crank
• High torque output
• Mounted on heavy-duty baseplate
• In-line direct-drive operation helps ensure equal amounts of pressure applied to the 650 ram/operation
• Does not include the Dillon Precision XL650 reloading press
• Completely compatible with the leading bullet feeders on the market

Rolling Handle for XL650 and RL550

Ball bearing rolling handle for effortless reloading.

Included thread lock. 

Weights in a 270 grams so you know heavy duty made to last a lifetime and thereafter.