Reloading equipment

Locator Buttons are sold individually. Adjust the quantity if you need more than one. For 550, 650, 750, 1050 and Square Deal machines.

Lee Replacement decapping pin for Decapping Die (#90292)

Includes: 4-Grade 5 Hex Bolts, 4- Nuts, 4 Flat Washers, 4-Fender Washers, 2-Wood Screws.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machines and the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machinesand the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

A Primer Flip Tray is a “must have” item for most reloaders.

There are many on the market to choose from but here at DAA, we strive to design things better, and we believe we have succeed with our DAA Primer Flip Tray.

The DAA Primer Flip Tray is made larger than most, and square in shape, to make it easier to empty a box of primers onto the tray. Even the very large box of the popular Federal primers easily fits within the footprint of our tray.

Much experimentation and finetuning was done on the serrations to make the tray as efficient and fast to use as possible. Just a few shakes of the wrist will flip all your primers Anvil side up.

The tray is made from a tough translucent plastic material, making it possible to see the primers through the tray as you flip it over. Enabling you to keep the primers well spread out for easy pickup.

But the most unique and innovative feature of our primer tray, solves an irritating issue well known to all primer flip tray uses!

Other Primer Flip Trays all have a sharp cornered side-wall on their lids. Because of this, when primers are close up against the side-wall they are very difficult to pick up. This forces uses to shuffle the tray to move the primers away from the wall.

However, the lid of the DAA Primer Flip Tray has a side-wall which is a 45 degree angled slope. This allows you to easily pick up the primers even when they are tight up against the side wall of the lid, saving you valuable time as you fill your primer tubes.

Since we introduced our DAA Turbo Case-Feeder Plate for the Dillon case feeders, we’ve had Mark-7 customers asking us if they could use it with their High Speed 11” Mark7 case feeder (as supplied with the Apex-10 press). The answer is YES! The disk is the same size and it works great in the excellent Mark-7 case feeder. 

The DAA Dislodge-Wedge is designed to be much larger and longer than the original Dillon part, reaching down to the very base of the plate, and providing a more gradual, angled surface to clear stacked cases as the disc rotates, at any speed.