Reloading equipment

If primer does not explode when hit by firing pin then most common reason is that primer is not seated deep enough. This problem is quite common in new XL750 since orginal primer punch spring is a little to long and primers are not seated deep enough. Armanov solution to this problem is new Index Cam Block with integrated ball bearing and adjustable primer seating depth stop.

Powder Baffle for Dillon is a must have reloading accessory that dramatically increases powder load consistency and accuracy! 

Armanov Ball Bearing Alu Roller Handle gives you an entirely new “feel.” A roller handle reduces operator fatigue during long reloading sessions and makes primer seating easier. Angled model fits the Hornady reloading press machine.

Rolling Handle for XL650/750 and RL550.

Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.

This is a Debris Catcher for Casefeeder. The Dillon Casefeeder has two holes in the bottom back of the bowl assembly. These holes allow any accumulated spent powder, polishing media or general crud to drain out of the bowl. This debris if left unchecked can fall all over your press or bench top.

Tired of emptying your spent primer cup or knocking it over spilling spent primers everywhere?

Install Armanov Spent Primer Chute and forget about It. Zero mods to reloading press required, it re-uses the original screw to install and installs in place of stock spent primer cup bracket.

Primer cam Index Stop Switch for Dillon Precision XL650 and SL900 Progressive Reloading Press. The switch moves to turn ON and OFF the index by bypassing the indexing lever on the primer feed assembly.

Primer chute for spent primers replaces the blue plastic spent primer cup and bracket on the Dillon XL650/750 reloading press. It completely covers the spent primer ejection port, creating a fully enclosed pathway for spent primers. Spent primers are routed through clear PVC tubing into plastic bottle which you fix with a holder on a strong mount. No more spent primers on floor.

This toolhead has lock rings that allow the sizer and seater dies to float. This floating action allows the dies to center themselves exactly over each cartridge for the best possible alignment and more concentric ammunition.

This spacer for Dillon case feeder allows you quickly rise your case feeder plate without clutch system disassembly.

Free Float Lock Ring for Dillon Toolhead allow the sizer and seater dies to float. This floating action allows the dies to center themselves exactly over each cartridge for the best possible alignment and more concentric ammunition. This free float lock ring will only fit with free float toolheads for Dillon XL650 / XL750 or RL550..

Powder measure knob for the Dillon Powder thrower with click for easy adjustment. Unlike other competitors, this knob is laser etched with 50 graduations giving the user reference points when adjusting. Two steel spring loaded balls generate smooth and repetable clicks. Easy to setup between multiple loads or even calibres, very precise 50 clicks per turn. 

Live Primer Catcher is practical solution to a problem every XL650 press user is familiar with: live primers being ejected out of the press and falling to the floor. The original ramp on the press does not do a great job catching those live primers as they are ejected. And even if they stay on the ramp, retrieving them without dropping some can be challenging.

This toolhead for Dillon Super 1050/RL1100 is a real game-changer. It is a drop-in upgrade for the original toolhead with great new features.

Bushings are made for a quick, simple and precise change of dies in the toolhead. No need for a complete toolhead change anymore, just twist and replace any bushing with the die of your choice. Change six dies on a Dillon Super 1050 / RL 1100 in seconds!

Armanov Mirror for Dillon Case Feeder is a simple solution for keeping control of quantity of cases inside case feeder.

Powder Funnel for activating the Dillon automatic powder system. An essential component for reloading 9 mm family of calibers with any bullet-feeder system with your Dillon powder measure. It prepares the brass correctly so that the bullet can be seated in the case, and not tip over as you index the shell plate.

Primer Stop Block for Dillon Precision XL750 Progressive Reloading Press. Comes very useful for operations when no primer insertion is required. The block prevents movement of the primer slide bar. Super simple installation by simply inserting the block between the pin on the slide and primer feed body. When not in use attach it to the steel primer tube by the magnet

Install by slipping this on the top back side of your case feeder and fits to the Dillon Case feeder 550 / 650 / 750 / 1050 / 1100 or Hornady LNL AP Bullet / Case feeder support tubes.

Armanov Quick Disconnect replaces original Dillon Powder Measure half-ring retention.

Primer chute for spent primers replaces the blue plastic spent primer cup and bracket on the Dillon XL650, 750 and Super 1050/1100 reloading press. It completely covers the spent primer ejection port, creating a fully enclosed pathway for spent primers. Spent primers are routed through clear PVC tubing into any convenient waste container.

Designed for the whole conversion kit: Casefeed Body Bushing, Shell Plate, Casefeed Adapter, Station Locator, Powder Funnel and Locator buttons.

This toolhead is required for use with RT1500 Electric Case Trimmer. This combination is commonly used to trim 300 AAC Blackout on the XL650 & XL750.

Designed for economy of motion when loading. Our new bullet tray is made of durable cast aluminum and is powder coated Dillon Blue. Fits RL 1050 / Super 1050.

Carbide sizing die 9MM Luger Carbide Full Length only. No case lube needed.

As any reloader knows, adjusting a die on a tightly spaced tool head can be difficult and aggravating. The die nuts and various machine parts do not allow easy access and using regular wrenches can be near impossible. The DAA 1 Inch Box-End Wrench is the solution to this problem! The custom made, laser cut, stainless steel wrench is strong enough to last a lifetime and thin-walled enough to fit between any dies for easy access and adjustment.

A common question we hear is “Can I use the Bullet Feeder on my 550?” Or “Can I use the Bullet Feeder and still continue to use my powder check on my 650?”.

Such Seating and Crimping dies are available, and so we decided it was time we made them directly available to our customers as well. LEE Precision produces these, so no question about the quality. 

The 2-in-1 Seating and crimping die include an O-ring lock machined into the nut, which allows you to hand tighten only – and the die stays put! They include a finger adjustable floating bullet seater. For durability they are heat treated to ideal hardness and polished to the smoothest finish.

DAA XL650/750 Debris-Out Casefeeder Adaptor, which replaces the original Dillon case feeder adaptor on your press, the slots cut in the pipe allow the debris to fall out the sides onto the small collection tray and the chances of a jam-up are greatly reduced.

Many customers choose to start reloading on their XL650/750 without the optional case feeder, and for them the new DAA Mini Case feeder will be a great addition to their press!

The DAA Dislodge-Wedge is designed to be much larger and longer than the original Dillon part, reaching down to the very base of the plate, and providing a more gradual, angled surface to clear stacked cases as the disc rotates, at any speed.

Double the capacity of your Dillon powder hopper with this clear PT extended Hopper. The Hopper measures 36cm long and replaces the 18cm long Dillon Original.

It assembles in the same way, using the two screws in place on the Dillon.

>span class="s1">An acrylic powder baffle is included with the extended hopper.

1050 users, please note: this hopper it too long to fit under the case feeder on your 1050. You will need to shorten it to fit. The tube can be shortened using a saw or serrated knife. About 9cm need to be cut off to fit under the 1050 case feeder.

The DAA Infra-Red Low Powder Sensor is an efficient, high-tech solution to a problem every reloader has encountered: Making sure to fill that powder hopper in time, before you accidently load empty cases without powder… (don’t feel stupid, we’ve all done it…)