Reloading equipment

Until now, reusing military brass, with its crimped primer pockets, has been a tedious task. The Dillon solution is a remarkably simple device that bolts to your bench and allows you to swage the primer pockets with speed and ease. The case is supported from the inside, so you won't be tearing the rims off the brass. A tool steel, hardened swage rod (easy to change from large to small primers) simply rolls the crimp away. No reaming is necessary. Our unique compound cam leverage system assures not only ease of operation, but perfect alignment with each and every round. Sound simple? It is and it works. What's more, it's inexpensive. The Super Swage 600 comes with large and small swage rods, .22 and .30 caliber backup rods, and a 45ACP adapter. 

Spare parts kit specifically for your RL550 machine keeps your machine running also when you had a little accident. Don't risk downtime waiting for a replacement parts! Contains everything you need to keep your Dillon loader cleaned and lubricated up to factory specifications. Includes the spare parts kit for your machine.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machinesand the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

Some Mr.BulletFeeder users have asked for the option to extend the output feed spring, to allow them to position the collator further away, or perhaps position one collator between two presses and use it to alternately feed each machine.

To meet this request we are pleased to offer the output springs and a screw-on adaptor cap which will allow you to attach to your current spring and extend it up to another 38cm.

 Two sizes are available. The Small (10mm inner diameter) matches the springs used with the rifle caliber machines and the large size (12mm inner diameter) as shipped with the pistol calibers.

 Note that some “do it yourself” supports for the spring will be needed to prevent it sagging under the weight of the bullets. You do need to keep the tube running downwards and prevent bullets from “pooling” in a sagging loop.

A replacement threaded die body for your Mr.Bulletfeeder by DAA Dropper. This threaded body is compatible with all calibers.

The 2018 Hanger Assembly for the Mr.Bulletfeeder by DAA ships as standard with all new units leaving DAA as of Jan 2018.

Should you wish to upgrade your current hanger assembly (the one with the round Delrin pucks and aluminum rods) you can do so by purchasing this new hanger separately. It is reverse-compatible with all previous Mr.Bulletfeeder by DAA units.

The new hanger is a simplified design, which makes assembly and adjustments to the tilt angle easier and faster to make. The Horizontal aluminum bracket clamps directly onto the motor gear box, allowing for easy assembly on either the left or the right side of the collator, to accommodate your specific position mounting needs.

The vertical piece hangs over the side of your case feeder, and connects to the horizontal bracket by means of a large M8 bolt, which can be loosened and rotated for tilt adjustments.

Sturdy attachment to the collator, a simplified design with fewer parts, thick aluminum profiles and way fewer screws make this hanger simpler and easier to setup and adjust.

Note: Machine NOT included - only Hanger. 

The Dropper Assembly is needed for shooters who wish to set up a second tool-head in the same caliber, and wish to quickly transition from, say, 9mm to .38super. Or from one 9mm bullet to another. A change is needed to the collator parts, and if a 2nd tool-head is to be used on the progressive reloader, it is quicker and easier to leave an adjusted Mr.Bulletfeeder dropper on each tool-head. This allows for quick swapovers, without the need to calibrate or adjust the dropper. Note that in most cases you will need to purchase an additional Powder Funnel for your second tool-head’s powder measure, as our expanding powder funnel is required for troublefree reloading.

The Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder.

Kit contains QTY 5 of 301-1178 Shell plate springs 0.094" Dia, 0.018" Wire Dia, 302 SS cut to approximate length.

Also contains QTY 2 1" sections of 201-1210 Case Retention Spring 0.125" OD, 0.02" Wire Dia

Mark 7® 650 PRO Autodrive

Differentiating Features  

• Includes the Mark 7 Optical Decapping Sensor - a $200 value !
• Completely compatible with Mr. Bulletfeeder and GSI bulletfeeders
• Broad caliber capacity - able to load a wider array of calibers including larger rifle calibers
• Small footprint
• Digital clutch - adjustable on-the-fly from 0 to 20
• Digital primer depth setting - no more guessing !
• Digital jog and immediate stop
• Microprocessor monitored and controlled
• Includes pre-loaded computer tablet - no control boxes!
• Features monitored by computer
• Downloadable software upgrades for life
• Supports a variety of accessories
• User-configurable Dwell time at the top of the stroke as well as the bottom
• Easy Installation
• Pre-assembled and shipped ready to use
• CNC grade planetary gearbox
• Full warranty
• High torque motor - same available torque to machine as the 1050 X Autodrive
• Fully Supports International Voltage - this unit operates at 110/220v and at 50/60 Hz with no appreciable variation in speed or performance

Dimensions and Capacity

• Overall machine dimensions are 49" tall (124.4 cm) X 14" (35.5cm) wide x 12" (30.5cm) deep x 1/2" (1.27cm) thick
• True operational height: earlier machines 52.5", later machines 48.5"
• User selectable speeds from 900 to 1,800 rounds per hour
• Quite operation approximately at 75-80 dB including case and bullet feeder

650 Autodrive Specifics

• CNC billet heavy-duty crank
• High torque output
• Mounted on heavy-duty baseplate
• In-line direct-drive operation helps ensure equal amounts of pressure applied to the 650 ram/operation
• Does not include the Dillon Precision XL650 reloading press
• Completely compatible with the leading bullet feeders on the market