Zubehör

Until now, reusing military brass, with its crimped primer pockets, has been a tedious task. The Dillon solution is a remarkably simple device that bolts to your bench and allows you to swage the primer pockets with speed and ease. The case is supported from the inside, so you won't be tearing the rims off the brass. A tool steel, hardened swage rod (easy to change from large to small primers) simply rolls the crimp away. No reaming is necessary. Our unique compound cam leverage system assures not only ease of operation, but perfect alignment with each and every round. Sound simple? It is and it works. What's more, it's inexpensive. The Super Swage 600 comes with large and small swage rods, .22 and .30 caliber backup rods, and a 45ACP adapter. 

Square Deal B Caliber Conversions allow you to change from one caliber to another in minutes.  Caliber conversions are available for common straight walled handgun and carbine cartridges from 32 S&W Long through 45 Colt. 

Conversions include: 

• carbide size die (except .44-40)
• expander/powder funnel
• seat die
• crimp die
• shellplate
• locator buttons

The DAA Bullet Puller is a must-have for serious reloaders. This tool takes all the hassle out of separating your used cases from the bullet and powder. The tool itself is formed from high-quality plastic with an aluminum rod to ensure many years of durable performance.

The DAA Bullet Puller can be used for ammunition of all sizes ranging from .17 Remington to .50/70 Government cases. This tool comes with an extra set of three collets, should the originals happen to break. The tool itself is virtually indestructible and makes quick work of disassembling your ammunition for reloading.

Primer cam Index Stop Switch for Dillon Precision XL-650 and SL-900 Progressive Reloading Press. The switch moves to turn ON and OFF the index by bypassing the indexing lever on the primer feed assembly. Integrated spring ball works as clickable position capture. Use the factory screw to install. Material for the base is 6082 aluminium and material for the ramp is Delrin (POM-C). Spare ramps can be ordered separately. Super simple install. Just unscrew original primer cam and use same bolt to attach this stop switch.

Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.

The DAA XL650 Debris-Out Casefeeder Adaptor is the answer to a real problem many reloaders are all too familiar with: when cleaning brass with corncob or other dry media, often small bits of media remain mixed with the brass, and are fed down the case feeder tube. When they reach the tighter diameter of the adaptor tube, they wedge against the cases, causing a feeding jam. You then have to stop reloading, take apart the feeding pipe, clear the jam and only then continue.

But with the new DAA XL650 Debris-Out Casefeeder Adaptor, which replaces the original Dillon case feeder adaptor on your XL650, the slots cut in the pipe allow the debris to fall out the sides onto the small collection tray (we like to keep our workbench clean and neat!) and the chances of a jam-up are greatly reduced.

A drop on fit to your Dillon XL650. 

Not suitable for use on other Dillon reloading models, and cannot be used in conjunction with the DAA XL650 Mini case feeder.

he DAA Output Chute can be attached to any reloading press, hanging onto the same bracket which usually holds the Akro-Bin, and replacing it.

The long, 120cm (4ft) feed spring enables you to run the ammo down to a container on the floor, sparing you the need to empty that bin as you reload, and uncluttering your reloading press.

A characteristic of virtually all progressive reloading machines, regardless of brand, is that the dies are set rather close together. When you are first setting up a "naked" machine, there is plenty of wrench room, but if you have a need to adjust a die afterward, it often requires a delicate touch to maneuver a lock ring on a crowded toolhead. 
Dillon Precision has addressed this in two ways. We now offer new 1" die lock rings and a 1" Bench Wrench to fit them. This combination gives much more room to re-adjust dies after they're already mounted. The opposite end of our new wrench is a 7/16" box-end for adjusting the Powder Bar of any Dillon Powder Measure. Our new lock rings fit any standard 7/8" x 14 dies.

Dillon's new Toolholder fits your XL 650 and ensures that the tools you need to service your reloader are handy and organized. No more digging around your bench trying to find the right size hex wrench! This unit includes a complete allen wrench set plus the one inch bench wrench.

Dillon's new Toolholder fits your Square Deal B and ensures that the tools you need to service your reloader are handy and organized. No more digging around your bench trying to find the right size hex wrench! This unit includes the complete allen wrench set plus the new Square Deal bench wrench.

The Dillon Magnum Rifle Powder bar throws charge weights from 50 grains up to approximately 72 grains of extruded powder, or up to approximately 82 grains of ball/spherical powder

The Dillon Precision Universal Decapping Die is a standard 7/8"-14 die with a solid, hardened steel, decapping pin in an unlined steel die body.  The Universal Decapping Die allows you to remove spent primers without any resizing of the brass. 

• Works with all standard pistol and rifle cartridge sizes from 22 through 45. 
• Allows you to remove spent primers prior to trimming with our RT1500 Electric Case Trimmer.
• The Universal Decapping die allows brass to be deprimed prior to cleaning when processing brass.  Cleaner primer pockets help to maintain consistent primer seating depth and ignition.
• The Universal Decapping die works in all machines that accept standard 7/8"-14 dies.

Increase the stability of your reloading bench with Dillon's new Strong Mounts. These heavy gauge steel Strong Mounts increase the machine's "foot-print" to over 10", spreading the load over the bench instead of stressing the leading edge. 
Strong Mounts raise your machine 8", providing a comfortable work height for people who prefer to stand while reloading. 
All mounts come with all the fasteners necessary to mount your machine and are coated with a durable black wrinkle finish.

With a quick change assembly and a caliber conversion kit (sold separately), you can convert your RL 550 Series press from one caliber to another in less than a minute. 

Includes: 

• Powder measure
• Powder die
• Toolhead 
• Toolhead stand

Powder measure knob for the Dillon Powder thrower with click for easy adjustment.

Unlike other competitors, this knob is laser etched with 50 graduations giving the user reference points when adjusting. Two steel spring loaded balls generate smooth and repetable clicks. Easy to setup between multiple loads or even calibres, very precise 50 clicks per turn. Testing on pistol powders one click increments is about 0.015 grains. This is a very precise setting. 

Simple installment and a tremendous help for if you are using different loads with visual scale.

The Dillon Factory screw requires a wrench when adjusting the amount of powder to dispense in your powder thrower. This knob is labeled with graduations for orientation and easily allows the user to hand adjust the powder dispenser without the need for tools. Works on Dillon 1050, 650,550, SDB and 900 presses.

Both parts are made from aircraft grade aluminum - anodized black color

1 x laser etched knob assembly consisting of one knob frame and one adjusting knob

1 x allen wrench for the grub-screws to fasten

Dillon Powder Bar shown only for reference and is NOT included.

These lighter weight Aluminum toolheads are machined from billet using the same precise CNC machining as our standard toolheads. Available in four different colors to allow you to quickly differentiate between calibers or load types.

This packcloth nylon machine cover comes equipped with a D-ring, allowing the heavy-duty zipper to be locked.Covers XL650 with or without the case feeder attached. Additionally, use this cover for the RL550 when equipped with the optional handgun caliber case feeder. 

If you have an XL650 equipped with a Mr. Bulletfeeder, use the 1050 cover. 

This unit includes the complete allen wrench set