Accesories

Designed for the whole conversion kit: Casefeed Body Bushing, Shell Plate, Casefeed Adapter, Station Locator, Powder Funnel and Locator buttons.

As any reloader knows, adjusting a die on a tightly spaced tool head can be difficult and aggravating. The die nuts and various machine parts do not allow easy access and using regular wrenches can be near impossible. The DAA 1 Inch Box-End Wrench is the solution to this problem! The custom made, laser cut, stainless steel wrench is strong enough to last a lifetime and thin-walled enough to fit between any dies for easy access and adjustment.

Live Primer Catcher is practical solution to a problem every XL650 press user is familiar with: live primers being ejected out of the press and falling to the floor. The original ramp on the press does not do a great job catching those live primers as they are ejected. And even if they stay on the ramp, retrieving them without dropping some can be challenging.

Primer chute for spent primers replaces the blue plastic spent primer cup and bracket on the Dillon XL650, 750 and Super 1050/1100 reloading press. It completely covers the spent primer ejection port, creating a fully enclosed pathway for spent primers. Spent primers are routed through clear PVC tubing into any convenient waste container.

Install by slipping this on the top back side of your case feeder and fits to the Dillon Case feeder 550 / 650 / 750 / 1050 / 1100 or Hornady LNL AP Bullet / Case feeder support tubes.

Powder Funnel for activating the Dillon automatic powder system. An essential component for reloading 9 mm family of calibers with any bullet-feeder system with your Dillon powder measure. It prepares the brass correctly so that the bullet can be seated in the case, and not tip over as you index the shell plate.

If primer does not explode when hit by firing pin then most common reason is that primer is not seated deep enough. This problem is quite common in new XL750 since orginal primer punch spring is a little to long and primers are not seated deep enough. Armanov solution to this problem is new Index Cam Block with integrated ball bearing and adjustable primer seating depth stop.

This enhanced heat-treated toolhead washer and hex key bolt reduces any flexing of your toolhead, increasing the rigidity and potentially the consistency of your ammunition. This works on the RL1050 and Super 1050 as well as the RL1100 loader. Requires a 1/2" hew key wrench to install and remove the bolt.

The DAA Infra-Red Low Powder Sensor is an efficient, high-tech solution to a problem every reloader has encountered: Making sure to fill that powder hopper in time, before you accidently load empty cases without powder… (don’t feel stupid, we’ve all done it…)

Primer Stop Block for Dillon Precision XL750 Progressive Reloading Press. Comes very useful for operations when no primer insertion is required. The block prevents movement of the primer slide bar. Super simple installation by simply inserting the block between the pin on the slide and primer feed body. When not in use attach it to the steel primer tube by the magnet

Bushings are made for a quick, simple and precise change of dies in the toolhead. No need for a complete toolhead change anymore, just twist and replace any bushing with the die of your choice. Change six dies on a Dillon Super 1050 / RL 1100 in seconds!

This toolhead is required for use with RT1500 Electric Case Trimmer. This combination is commonly used to trim 300 AAC Blackout on the XL650 & XL750.

The DAA Dislodge-Wedge is designed to be much larger and longer than the original Dillon part, reaching down to the very base of the plate, and providing a more gradual, angled surface to clear stacked cases as the disc rotates, at any speed.

Eemann Tech Springs Kit for Dillon XL650.

Eemann Tech Springs Kit for Dillon RL550.

Eemann Tech Springs Kit for Dillon RL1050.

This toolhead for Dillon Super 1050/RL1100 is a real game-changer. It is a drop-in upgrade for the original toolhead with great new features.

Many customers choose to start reloading on their XL650/750 without the optional case feeder, and for them the new DAA Mini Case feeder will be a great addition to their press!

Armanov Mirror for Dillon Case Feeder is a simple solution for keeping control of quantity of cases inside case feeder.

Tired of emptying your spent primer cup or knocking it over spilling spent primers everywhere?

Install Armanov Spent Primer Chute and forget about It. Zero mods to reloading press required, it re-uses the original screw to install and installs in place of stock spent primer cup bracket.

This is a Debris Catcher for Casefeeder. The Dillon Casefeeder has two holes in the bottom back of the bowl assembly. These holes allow any accumulated spent powder, polishing media or general crud to drain out of the bowl. This debris if left unchecked can fall all over your press or bench top.

This toolhead has lock rings that allow the sizer and seater dies to float. This floating action allows the dies to center themselves exactly over each cartridge for the best possible alignment and more concentric ammunition.

The DAA Magnetic Powder Check 2.0 (US Pat. Pending) is a great addition to any progressive reloading machine, helping to ensure the quality and safety of your reloaded ammo. The unique new design uses a high-tech Reed Sensor and a magnet assembled to the plunger Rod, to assess if the charge in the case is of the correct height.

Double the capacity of your Dillon powder hopper with this clear PT extended Hopper. The Hopper measures 36cm long and replaces the 18cm long Dillon Original.

It assembles in the same way, using the two screws in place on the Dillon.

>span class="s1">An acrylic powder baffle is included with the extended hopper.

1050 users, please note: this hopper it too long to fit under the case feeder on your 1050. You will need to shorten it to fit. The tube can be shortened using a saw or serrated knife. About 9cm need to be cut off to fit under the 1050 case feeder.

Designed to be used XL650/XL750, Suepr1050/RL1050/RL1100. The speed of the casefeeder is controlled by a potentiometer on the casefeed funnel. It allows you to infinitely regulate the speed from 0 to 8 RPM. The motor features a universal power supply for both domestic and foreign voltages. Adaptable to either 110 or 220 Volt, 60 or 50 hz, you simply swap out the plug to the style appropriate to your region. The bowl has an adjustable window cuff and cases deflector, for a larger range of cartridge capability. 

Dillon RL550 will produce match-quality ammo for over 160 different rifle and pistol calibers. These kits fit the RL300, RL450, RL550 series, AT500 and BL550 machines.

An automatic casefeed system, similar to the one used on Dillon's commercial-grade Super 1050 machine and the XL 650, is now available for your RL 550 series press.

Sizing/Depriming Die
Our sizing/depriming dies feature a unique “floating decap assembly” with a snap spring that throws the spent primer off the pin and eliminates the problem of primer “draw back” that often occurs when decapping military brass. The primary feature of Dillon’s size die design the long, tapered carbide ring with a radiused opening remains unchanged. That radiused opening, and its importance to progressive reloading, is one of the reasons why our seat and crimp dies are better. We found a way of manufacturing these dies that has enabled us to make the lead-in radius even bigger! The bigger radius makes progressive loading with our equipment even smoother but that’s still only a part of the story.

Bullet Seating Die
Our new quick-disassembly seat die allows the user to disassemble and clean the seat die without losing adjustment. In this manner, bullet lube and shavings can be quickly removed from the die, thereby guaranteeing a constant seating depth. We’ve incorporated a “flip-flop” seating stem and a clip that enables you to remove the die insert and change the seating stem from round nose to semi-wadcutter without unscrewing a seating stem out of the die body. We’ve always included both types of seating stems, but the new double-ended design makes it a simple matter to remove a pin, reverse the seating stem, make any minor seating depth adjustments that may be necessary and go on loading in a fraction of the time it used to take.

Crimp Die
We’ve made it easy for you to remove the die insert for cleaning without having to change the critical crimp adjustment. Once your crimp die is set for the proper amount of crimp, you’ll never have to change it. This is especially good news for all of you who load lead bullets! Before, you had to unscrew the die from the toolhead and disassemble the die in order to remove any bullet lube or lead residue. Then, you had to start from square one to re-adjust the crimp. Those days are over. All you have to do now is pop a clip and the die insert drops into your hand for cleaning.

NOTE: All Dillon Pistol Die sets include our sizer/ decap die, seat die and a separate crimp die. (Taper crimp for autos; accu-crimp for revolvers.)

Dillon Precision Primer Magazine Tube Small SD/550/650/750/1050/1100.

NOTE:

• 14024 is only one plastic end piece.
• 22030 comes in a set of 1 magazine tube and 2 plastic end pieces.

The DAA Powder-Spill-Prevention (PSP) Brush is a simple yet efficient reloading accessory that solves a real issue: How to prevent small amounts of powder being spilled out of the case, as the tool head of the progressive reloading press indexes?

The Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder.

Rolling Handle for XL650/750 and RL550.

Free Float Lock Ring for Dillon Toolhead allow the sizer and seater dies to float. This floating action allows the dies to center themselves exactly over each cartridge for the best possible alignment and more concentric ammunition. This free float lock ring will only fit with free float toolheads for Dillon XL650 / XL750 or RL550..

The DAA Powder-Spill-Prevention (PSP) Brush is a simple yet efficient reloading accessory that solves a real issue: How to prevent small amounts of powder being spilled out of the case, as the tool head of the progressive reloading press indexes?

Primer chute for spent primers replaces the blue plastic spent primer cup and bracket on the Dillon XL650/750 reloading press. It completely covers the spent primer ejection port, creating a fully enclosed pathway for spent primers. Spent primers are routed through clear PVC tubing into plastic bottle which you fix with a holder on a strong mount. No more spent primers on floor.

Powder Baffle for Dillon is a must have reloading accessory that dramatically increases powder load consistency and accuracy! 

Mounts directly to Strong Mount. Fits the Square Deal, RL550 series and XL650 strong mounts. For 1050 machines use #22215. You must have a strongmount in order to use this bullet tray.

An additional 6-tube Magazine Assembly for your Mini XL650 Case Feeder. It will hold about 150 pcs of 9mm brass, 130 pcs of .40 and about 120 pcs of .38S.

Dillon Square Deal B Primer slide bearing.

Carbide sizing die 9MM Luger Carbide Full Length only. No case lube needed.

Lee Replacement decapping pin for Decapping Die (#90292)