Dillon 1050 and 1100

As any reloader knows, adjusting a die on a tightly spaced tool head can be difficult and aggravating. The die nuts and various machine parts do not allow easy access and using regular wrenches can be near impossible. The DAA 1 Inch Box-End Wrench is the solution to this problem! The custom made, laser cut, stainless steel wrench is strong enough to last a lifetime and thin-walled enough to fit between any dies for easy access and adjustment.

This enhanced heat-treated toolhead washer and hex key bolt reduces any flexing of your toolhead, increasing the rigidity and potentially the consistency of your ammunition. This works on the RL1050 and Super 1050 as well as the RL1100 loader. Requires a 1/2" hew key wrench to install and remove the bolt.

The DAA Infra-Red Low Powder Sensor is an efficient, high-tech solution to a problem every reloader has encountered: Making sure to fill that powder hopper in time, before you accidently load empty cases without powder… (don’t feel stupid, we’ve all done it…)

Bushings are made for a quick, simple and precise change of dies in the toolhead. No need for a complete toolhead change anymore, just twist and replace any bushing with the die of your choice. Change six dies on a Dillon Super 1050 / RL 1100 in seconds!

Eemann Tech Springs Kit for Dillon RL1050.

This toolhead for Dillon Super 1050/RL1100 is a real game-changer. It is a drop-in upgrade for the original toolhead with great new features.

Tired of emptying your spent primer cup or knocking it over spilling spent primers everywhere?

Install Armanov Spent Primer Chute and forget about It. Zero mods to reloading press required, it re-uses the original screw to install and installs in place of stock spent primer cup bracket.

This is a Debris Catcher for Casefeeder. The Dillon Casefeeder has two holes in the bottom back of the bowl assembly. These holes allow any accumulated spent powder, polishing media or general crud to drain out of the bowl. This debris if left unchecked can fall all over your press or bench top.

Designed to be used XL650/XL750, Suepr1050/RL1050/RL1100. The speed of the casefeeder is controlled by a potentiometer on the casefeed funnel. It allows you to infinitely regulate the speed from 0 to 8 RPM. The motor features a universal power supply for both domestic and foreign voltages. Adaptable to either 110 or 220 Volt, 60 or 50 hz, you simply swap out the plug to the style appropriate to your region. The bowl has an adjustable window cuff and cases deflector, for a larger range of cartridge capability. 

Sizing/Depriming Die
Our sizing/depriming dies feature a unique “floating decap assembly” with a snap spring that throws the spent primer off the pin and eliminates the problem of primer “draw back” that often occurs when decapping military brass. The primary feature of Dillon’s size die design the long, tapered carbide ring with a radiused opening remains unchanged. That radiused opening, and its importance to progressive reloading, is one of the reasons why our seat and crimp dies are better. We found a way of manufacturing these dies that has enabled us to make the lead-in radius even bigger! The bigger radius makes progressive loading with our equipment even smoother but that’s still only a part of the story.

Bullet Seating Die
Our new quick-disassembly seat die allows the user to disassemble and clean the seat die without losing adjustment. In this manner, bullet lube and shavings can be quickly removed from the die, thereby guaranteeing a constant seating depth. We’ve incorporated a “flip-flop” seating stem and a clip that enables you to remove the die insert and change the seating stem from round nose to semi-wadcutter without unscrewing a seating stem out of the die body. We’ve always included both types of seating stems, but the new double-ended design makes it a simple matter to remove a pin, reverse the seating stem, make any minor seating depth adjustments that may be necessary and go on loading in a fraction of the time it used to take.

Crimp Die
We’ve made it easy for you to remove the die insert for cleaning without having to change the critical crimp adjustment. Once your crimp die is set for the proper amount of crimp, you’ll never have to change it. This is especially good news for all of you who load lead bullets! Before, you had to unscrew the die from the toolhead and disassemble the die in order to remove any bullet lube or lead residue. Then, you had to start from square one to re-adjust the crimp. Those days are over. All you have to do now is pop a clip and the die insert drops into your hand for cleaning.

NOTE: All Dillon Pistol Die sets include our sizer/ decap die, seat die and a separate crimp die. (Taper crimp for autos; accu-crimp for revolvers.)

Dillon Precision Primer Magazine Tube Small SD/550/650/750/1050/1100.

NOTE:

• 14024 is only one plastic end piece.
• 22030 comes in a set of 1 magazine tube and 2 plastic end pieces.

The Mini Mr.Bulletfeeder by DAA uses a 6-tube magazine system which holds roughly 100 bullets. It feeds into the same brilliantly reliable dropper die assembly as used on the Mr.Bulletfeeder.

The DAA Powder-Spill-Prevention (PSP) Brush is a simple yet efficient reloading accessory that solves a real issue: How to prevent small amounts of powder being spilled out of the case, as the tool head of the progressive reloading press indexes?

Spare parts kit specifically for your Super 1050 machine keeps your machine running also when you had a little accident. Don't risk downtime waiting for a replacement parts! Contains everything you need to keep your Dillon loader cleaned and lubricated up to factory specifications. Includes the spare parts kit for your machine.

Comes with powder check die and 3 check rods which are from .22 till .45 Cal. Battery AAA is included. 

Super 1050 Quick Change Kits allows you to leave your dies and powder charge set up and dedicated to a specific cartridge for faster, easier caliber changes.  Caliber changes require a caliber conversion kit (sold separately) in the caliber you want to add to your Dillon Super 1050. 

Don't risk downtime waiting for a replacement part!  Dillon Precision Spare Parts Kits keep your machine running without waiting for replacement parts to arrive in the mail.

This bin is 260mm long, 110mm wide by 120mm deep and is great for storing just about anything.

This heavy-duty nylon cover comes equipped with a D-ring, allowing the zipper to be locked. 

If you have a Mr. Bulletfeeder mounted onto your 1050, this cover will still cover the machine, but you must orient the cover so that the zipper is on the LEFT side, not the back. 

Armanov Quick Disconnect replaces original Dillon Powder Measure half-ring retention.

Designed for economy of motion when loading. Our new bullet tray is made of durable cast aluminum and is powder coated Dillon Blue. Fits RL 1050 / Super 1050.

Powder measure knob for the Dillon Powder thrower with click for easy adjustment. Unlike other competitors, this knob is laser etched with 50 graduations giving the user reference points when adjusting. Two steel spring loaded balls generate smooth and repetable clicks. Easy to setup between multiple loads or even calibres, very precise 50 clicks per turn. 

Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.