Reloading equipment

Primer chute for spent primers replaces the blue plastic spent primer cup and bracket on the Dillon XL650/750 reloading press. It completely covers the spent primer ejection port, creating a fully enclosed pathway for spent primers. Spent primers are routed through clear PVC tubing into plastic bottle which you fix with a holder on a strong mount. No more spent primers on floor.

Eemann Tech Springs Kit for Dillon XL650.

Live Primer Catcher is practical solution to a problem every XL650 press user is familiar with: live primers being ejected out of the press and falling to the floor. The original ramp on the press does not do a great job catching those live primers as they are ejected. And even if they stay on the ramp, retrieving them without dropping some can be challenging.

A characteristic of virtually all progressive reloading machines, regardless of brand, is that the dies are set rather close together. When you are first setting up a "naked" machine, there is plenty of wrench room, but if you have a need to adjust a die afterward, it often requires a delicate touch to maneuver a lock ring on a crowded toolhead. 
Dillon Precision has addressed this in two ways. We now offer new 1" die lock rings and a 1" Bench Wrench to fit them. This combination gives much more room to re-adjust dies after they're already mounted. The opposite end of our new wrench is a 7/16" box-end for adjusting the Powder Bar of any Dillon Powder Measure. Our new lock rings fit any standard 7/8" x 14 dies.

The DAA Bullet Puller is a must-have for serious reloaders. This tool takes all the hassle out of separating your used cases from the bullet and powder. The tool itself is formed from high-quality plastic with an aluminum rod to ensure many years of durable performance.

The DAA Bullet Puller can be used for ammunition of all sizes ranging from .17 Remington to .50/70 Government cases. This tool comes with an extra set of three collets, should the originals happen to break. The tool itself is virtually indestructible and makes quick work of disassembling your ammunition for reloading.

Powder funnels to activate the Dillon automatic powder system. 

Funnels labelled "oversize"require the separate XL Powder Die #21253 

Order from the drop down menu below. 

• Caliber Conversion Chart for the RL300, RL450, RL550 Series, AT500 and BL550  
• Caliber Conversion Chart for the XL650
• Caliber Conversion Chart for the Super 1050
• Caliber Conversion Chart for the Square Deal B 

A common question we hear is “Can I use the Bullet Feeder on my 550?” Or “Can I use the Bullet Feeder and still continue to use my powder check on my 650?”.

Such Seating and Crimping dies are available, and so we decided it was time we made them directly available to our customers as well. LEE Precision produces these, so no question about the quality. 

The 2-in-1 Seating and crimping die include an O-ring lock machined into the nut, which allows you to hand tighten only – and the die stays put! They include a finger adjustable floating bullet seater. For durability they are heat treated to ideal hardness and polished to the smoothest finish.

DAA XL650/750 Debris-Out Casefeeder Adaptor, which replaces the original Dillon case feeder adaptor on your press, the slots cut in the pipe allow the debris to fall out the sides onto the small collection tray and the chances of a jam-up are greatly reduced.

Armanov Quick Disconnect replaces original Dillon Powder Measure half-ring retention.

Install by slipping this on the top back side of your case feeder and fits to the Dillon Case feeder 550 / 650 / 750 / 1050 / 1100 or Hornady LNL AP Bullet / Case feeder support tubes.

Stop switch enables you to lock the case feed shuttle back to prevent cases from feeding into the shell plate when cycling the press. Easy installation. Just screw with two original bolts. Built in hinge made for super easy usage, cycle machine to down position and enable stop switch. Built in bulge that locks switch in case ON position.  Great for clearing the shell plate, maintenance, setup, or any time you don’t want cases to feed.  Made from high quality steel. This product is suitable for Dillon 1050 only.

When you need to pull some bullets for whatever reason, and impact style tool is the easiest method. Just one stern “whack” and the bullet is separated from the brass. It is that easy. Three different collets are included allowing you to pull bullets  from just about every caliber rimmed or rimless. Versatility makes this bullet puller the only one to have.

Dillon Precision Primer Magazine Tube Small SD/550/650/750/1050/1100.

NOTE:

• 14024 is only one plastic end piece.
• 22030 comes in a set of 1 magazine tube and 2 plastic end pieces.

Double the capacity of your Dillon powder hopper with this clear PT extended Hopper. The Hopper measures 36cm long and replaces the 18cm long Dillon Original.

It assembles in the same way, using the two screws in place on the Dillon.

>span class="s1">An acrylic powder baffle is included with the extended hopper.

1050 users, please note: this hopper it too long to fit under the case feeder on your 1050. You will need to shorten it to fit. The tube can be shortened using a saw or serrated knife. About 9cm need to be cut off to fit under the 1050 case feeder.

he DAA Output Chute can be attached to any reloading press, hanging onto the same bracket which usually holds the Akro-Bin, and replacing it.

The long, 120cm (4ft) feed spring enables you to run the ammo down to a container on the floor, sparing you the need to empty that bin as you reload, and uncluttering your reloading press.